Descargar Imprimir esta página
Cooper Lighting Iris M-32T Instrucciones De Instalación
Cooper Lighting Iris M-32T Instrucciones De Instalación

Cooper Lighting Iris M-32T Instrucciones De Instalación

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ADI140857
Installation Instructions – M-32T, M-5MR, M-5P30 & M-5P36
Instructions d'installation – M-32T, M-5MR, M-5P30 & M-5P36
Instrucciones de instalación de las luminarias M-32T, M-5MR,
M-5P30 & M-5P36
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
WARNING
Read and understand these instructions before
installing fixture. To prevent electrical shock,
be sure power is turned off before installing or
servicing this fixture.
INSTALLATION
General Installation for All Modules
Lamp Modules can be installed into platforms before
installation into the ceiling or after the ceiling is
installed.
Remove cardboard overspray protector and
reinstall after Module installation to protect interior
of platform from paint and construction dirt.
Power connections are done via polarized three wire
quick connects. The three wire female connector
is located 1" above the frame next to the access
door. The access door may need to be removed
depending on which module is to be installed.
(Figure 1.)
Optical elements are keyed to provide proper
orientation of optics. A dropped finger will fit into
a notch on the reflector assembly to allow it to
pull tight to ceiling. If trim does not seat properly
against the ceiling, rotated it 180° and insert again.
(Figure 2.)
M-32T Compact Fluorescent 32W Triple Tube
Lamp Module
1.
Loosen thumbscrews holding access door,
remove door by lifting vertically to disengage from
thumbscrews. Remove access door from fixture.
2.
Insert M-32T access door with ballast mounted
to it through aperture. Position door to replace
original door. Slide door down vertically over
thumbscrews. This can be done without removing
thumbscrews from housing. Tighten thumbscrews
to firmly hold door into place. (Figure 1.)
3.
Plug Quick connect into platform receptacle.
N
otee:
Iris® recessed fixtures are designed to meet
the latest NEC requirements and are UL listed
and CSA certified. To assure full compliance with
local codes and regulations, check with your local
electrical inspector before installation.
4.
Socket is inserted into the top of the reflector and two
thumbscrews are tightened. Some reflectors allow for
two lamp positions- move socket into proper position
for optimal performance. See label on reflector for
proper location. (Figure 3.)
5.
Install reflector element and lamp. For best
performance use 4-pin compact fluorescent lamps all
by a single manufacturer.
M-5P30 Line Voltage Adjustable Accent Module
1.
Plug Quick Connect into platform receptacle.
2.
Install Adjustable Accent mechanism into ceiling
aperture. Ring is keyed into platform by aligning notch
in ring with dropped finger on platform. Three springs
on Adjustable Accent ring snap into notches. (Figure 4.)
3.
Install lamp, and then install reflector.
Figure 1.
Dropped
Finger
Align
Notch
Figure 2.
TM
INS #
Access Door
Three Wire Female
Connector
Wall Wash
Thumbscrew
Position
Downlight
Position
Figure 3.

Publicidad

loading

Resumen de contenidos para Cooper Lighting Iris M-32T

  • Página 1 INS # ADI140857 Installation Instructions – M-32T, M-5MR, M-5P30 & M-5P36 Instructions d’installation – M-32T, M-5MR, M-5P30 & M-5P36 Instrucciones de instalación de las luminarias M-32T, M-5MR, M-5P30 & M-5P36 IMPORTANT: Read carefully before installing fixture. Retain for future reference. otee: Iris®...
  • Página 2 Installation Instructions – M-32T, M-5MR, M-5P30 & M-5P36 applications. The blue labeled lamp connector is for use in M-5MR, M-5P36: Low Voltage Adjustable Accent “switched” applications. Module Dimmers lower the primary voltage from 120v to otee: Loosen thumbscrews holding access door, remove door 115v or less, and therefore the transformer will by lifting vertically to disengage from thumbscrews.
  • Página 3 Instructions d’installation – M-32T, M-5MR, M-5P30 & M-5P36 IMPORTANT: Lisez attentivement avant d'installer le luminaire. Conservez pour une référence future. Les dispositifs d’éclairage encastrés Iris® sont otee: AVERTISSEMENT conçus pour répondre aux normes NEC les plus récentes, et sont homologués UL et certifiés CSA. Veuillez lire attentivement les instructions avant d’installer ce dispositif d’éclairage.
  • Página 4 Instructions d’installation – M-32T, M-5MR, M-5P30 & M-5P36 M-5MR, M-5P36: Module de réglage d’intensité pour d’éclairage ou d’être déverrouillé pour tourner, ou d’être incliné. basse tension Desserrez les vis à serrage à main qui maintiennent On peut utiliser jusqu’à deux lentilles avec les lampes ●...
  • Página 5: Instalación

    Instrucciones de instalación de las luminarias M-32T, M-5MR, M-5P30 & M-5P36 IMPORTANTE: Lea atentamente antes de instalar la luminaria. Conserve estas instrucciones para tenerlas como referencia futura. ADVERTENCIA otee: Las unidades empotradas Iris® han sido diseñadas para cumplir con los requisitos actuales del Código Lea y comprenda estas instrucciones antes de instalar Eléctrico Nacional (NEC) y están aprobadas por UL y la unidad.
  • Página 6: Rotación Horizontal

    Instrucciones de instalación de las luminarias M-32T, M-5MR, M-5P30 & M-5P36 mantenerse alejados de la lámpara. M-5MR, M-5P36: Módulo de Foco Ajustable de Bajo Los transformadores magnéticos de bajo voltaje Voltaje ● ● requieren un equipo regulador de luz adecuado. Un Afloje los tornillos de ajuste manual que sujetan regulador inadecuado puede dañar los transformadores la puerta de acceso.
  • Página 8: Garantie Et Limitation De Responsabilité

    1000 Eaton Boulevard Cleveland, OH 44122 United States Eaton.com Eaton is a registered trademark. All trademarks are property Eaton’s Cooper Lighting Business of their respective owners. 1121 Highway 74 South Peachtree City, GA 30269 Eaton est une marque de commerce Cooperlighting.com déposée.

Este manual también es adecuado para:

Iris m-5mrIris m-5p30Iris m-5p36