Proper Use; Technical Data - EINHELL HOME TH-MS 2112 Manual De Instrucciones Original

3. Proper use

The crosscut and miter saw is designed for cross-
cutting wood and wood-type materials which are
appropriate for the machine's size. The saw is not
designed for cutting fi rewood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impos-
sible to eliminate certain residual risk factors. The
following hazards may arise in connection with
the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut inju-
ries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if ear-muffs are not used
as necessary.
•
Harmful emissions of wood dust when used
in closed rooms.
Anl_TH_MS_2112_SPK7.indb 20 Anl_TH_MS_2112_SPK7.indb 20
GB

4. Technical data

Asynchronous motor ...................... 230 V ~ 50 Hz
Input power .... S1 1400 Watt / S6 40% 1600 Watt
Idle speed n ......................................... 5000 rpm
0
Carbide saw blade .............. ø210 x ø30 x 2,8 mm
Number of teeth ............................................... 48
Weight.........................................................7,1 kg
Tilting range .................................. -45° / 0° / +45°
Mitre cuts ................................ 0° to 45° to the left
Sawing width at 90° ................ max. 120 x 55 mm
Sawing width at 45° .................. max. 80 x 55 mm
Sawing width at 2 x 45°
(double mitre cuts) ............................. 80 x 32 mm
Operating mode S6 40%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot it
may only be operated for 40% of the cycle at the
specifi ed rating and must then be allowed to idle
for 60% of the cycle.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ..................... 88.7 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 101.7 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a = 2.70 m/s
h
K uncertainty = 1.5 m/s
2
- 20 -
2
07.05.12 08:45 07.05.12 08:45