Serato Rane ONE Guia Del Usuario página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

25. Censor / Reverse: Press and hold this button to activate Censor, which temporarily reverses
the playback of the track. Release the button to resume normal playback from where it would
have been if you had never engaged the Censor function (i.e., as if the track had been playing
forward the whole time).
Press Shift and press this button to activate Reverse, which will reverse the playback of the track.
Press the button again to resume normal playback from wherever the audio playhead stops.
26. Pitch Fader: Move this fader to adjust the speed (pitch) of the track. You can adjust its total
range with the Pitch Range buttons.
27. Pitch Range / Keylock: Press one of these buttons to adjust the range of the Pitch Fader to
±8%, ±16%, and ±50%.
Press and hold Shift and then press this button to activate or deactivate Keylock: the key of the
song will lock to whatever position the pitch fader is at when Keylock is activated. This feature
allows you to change the speed of the song without changing the key.
28. Pitch Bend -/+: Press and hold one of these buttons to momentarily reduce or increase
(respectively) the speed of the track.
29. Shift: Press and hold this button to access secondary functions of other controls on ONE.
30. Cue / Previous: When the Deck is paused, you can set a Temporary Cue Point by moving the
platter to place the playhead at the desired location and then pressing the Cue Button.
During playback, you can press the Cue Button to return the track to this Temporary Cue
Point. (If you did not set a Temporary Cue Point, then it will return to the beginning of the track.)
If the Deck is paused, you can press and hold the Cue Button to play the track from the
Temporary Cue Point. Releasing the Cue Button will return the track to the Temporary Cue
Point and pause it. To continue playback without returning to the Temporary Cue Point, press
and hold the Cue Button, then press and hold the Play Button, and then release both buttons.
Press and hold Shift and then press this button to "stutter-play" the track by returning to the
beginning of the track and restarting playback.
31. Sync / Sync Off: Press this button to automatically match the corresponding Deck's tempo
with the opposite Deck's tempo and phase.
Press and hold Shift and press this button to deactivate Sync.
32. Start/Stop: Press this button to start and stop the platter. The LED around this button will be
dim when power is on and no track is playing, bright when a track is playing, and flashing red
when the track is near its end.
33. Performance Pads: These pads have different functions on each deck depending on the
current pad mode.
Note: See
Operation > Pad Modes
34. Hot Cue / Pitch Play: Press this button to enter Hot Cue mode. Press the button a second
time to enter Pitch Play mode.
Note: The Serato Pitch N Time plugin (not included) is required to use Pitch Play mode.
35. Saved Loop: Press this button to enter Saved Loop mode.
36. Roll / Auto Loop: Press this button to enter Roll mode. Press the button a second time to
enter Auto Loop mode.
37. Sampler / Scratch Bank: Press this button to enter Sampler mode. Press the button a second
time to enter Scratch Bank mode. In this mode, you can assign songs to each pad in the
software, and then tap the pad to quickly load the song from the specified starting point to the
deck. This is useful for preparing and performing with song samples for scratching.
38. Slicer / Slicer Loop: Press this button to enter Slicer mode. Press the button a second time to
enter Slicer Loop mode.
39. Parameter /: Use these buttons for various functions in each pad mode. Press and hold
Shift and use these buttons to access secondary parameters.
to learn how to use the pads in each mode, described below.
7

Publicidad

Tabla de contenido
loading

Tabla de contenido