Programming The Keypad - Tyco DSC WT5500 v1.4 Instrucciones De Instalación

Installation Instructions
The WT5500 Wireless Keypad is compatible with the PC9155 and
SCW9055/SCW9057 Wireless Panels.
Specifications
• Temperature range: -10°C to +55°C (14°F to 131°F)
• Humidity (MAX): 93%R.H.
• Plastic enclosure protection degree: IP30, IK04
• Power adaptor output voltage: 4.5V @ 0.5A
DC
• Models - US/Latin America: SA103A-0506-6U; Canada: SA103A-0506-6;
EU: SA103A-0506G-6; UK: SA106C-05BS; AUS./NZ: SA106C-05AS;
China: SA106C-05HS
• Battery: 4 AA, 1.5 V, Energizer Alkaline
• Low Battery Indication: 2.2 V
• WT5500 current draw: 50mA
• Wall-mount tamper
• 5 programmable function keys
• Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), AC (Green LED)
• Frequency: 433.92MHz (WT5500-433/WT5500P-433 only)
• Frequency: 868.35MHz (WT5500-868/WT5500P-868 only)
NOTE: DSC recommends that the keypad be powered by the AC adaptor
and the batteries for EN installations
NOTE: When the power adapter is used, batteries provide minimum 24h
back-up.
Unpacking
The WT5500 keypad package is available in five distinct configurations, Wall
Mount, Wall Mount w/Proximity, Desk Stand, Accessory Kit and Proximity
Tags Only. The contents of each are described below
Keypad contains patented technology for the Proximity Tag.
WT5500 - WALL MOUNT WT5500DMK - ACCESSORY KIT
• 1 WT5500 Keypad • 1 WT5500DMK Keypad
• 1 WT5500BRK Wall Bracket • 1 Hardware Pack
• 1 Installation Manual • 1 Power Adaptor
WT5500P - WALL MOUNT/PROX TAG
• 1 Inner Door Sticker
• 4 AA Batteries • 1 WT5500P Keypad
• 1 Hardware Pack • 1 WT5500BRK Wall Bracket
WT5500D - DESK STAND • 1 Installation Manual
• 1 WT5500 Keypad • 1 Inner Door Sticker
• 1 WT5500DMK Desk Stand • 4 AA Batteries
• 1 WT5500BRK Wall Bracket • 1 Hardware Pack
• 1 Installation Manual • 1 PT4 or PT8 Prox Tag (433MHz/868MHz)
• 1 Inner Door Sticker
• 1 Power Adaptor PROXIMITY TAGS ONLY
• 4 AA Batteries • 1 PT4 or PT8 Prox Tag (433MHz/868MHz)
• 2 Hardware Packs • 1 Installation Manual
Mounting
You should mount the keypad where it is accessible from designated points
of entry and exit. Once you have selected a dry and secure location, perform
the following steps to mount the keypad.
Wall Mounting Plate
1. Locate the screw holes (4) at each corner of the mounting plate.
Screw
Holes
Screw
Holes
2. Use the four screws provided to affix the mounting plate to the wall;
ensure the mounting tabs are facing you (see above diagram).
3. Align the four mounting slots in the WT5500 housing with the four
mounting tabs protruding from the mounting plate.
4. Slide the keypad into place.
5. Firmly but carefully snap the keypad down onto the mounting plate.
6. To fasten the keypad securely onto the mounting plate, locate the two
screw holes in the bottom of the mounting plate then, using the two
screws provided in the hardware pack, screw the keypad into place.
Desk Stand - WT5500D
1. Insert the four rubber feet (found
in the hardware pack) into the
indentations provided in the bot-
.
tom of the desk stand.
2. Place the desk stand on a secure,
uncluttered surface.
3. Align the four mounting slots in the WT5500 housing with the four
mounting tabs protruding from the desk stand.
4. Slide the keypad into place. Firmly but carefully snap the keypad down
onto the desk stand.
5. To fasten the keypad securely onto the desk stand, locate the two holes
in the top corners of the back of the desk stand. Using the two screws
provided, screw the keypad to the desk stand.
Apply Battery Power
1. Slide the keypad up and out from the mounting plate/desk stand
(removing the screws first if required). The bay for the four AA batteries
is open and visible at the back of the keypad.
2. Insert the batteries as directed on the back of the keypad. Ensure the
correct polarity is observed.
3. Replace the keypad on the mounting plate / desk stand.
Screw
Holes
Mounting
Tabs
Screw
Holes
CAUTION: Do not mix old batteries with new ones.
Mounting
Holes
Tamper
Switch
Batteries
Mounting
Holes
Apply AC Power
1. Slide the keypad up and out from the mounting plate / desk stand.
2. Locate the power adaptor jack at the back of the keypad housing.
3. Place the adaptor plug in the housing indentation, perpendicular to the
keypad. Insert the adaptor plug firmly into the jack.
4. Pivot the adaptor plug downwards so that it fits flush with the housing.
Guide the AC wire along the channel provided in the keypad housing;
the wire will extend through the bottom of the housing.
5. Replace the keypad on the mounting plate/desk stand (in the latter case, a
further channel is provided in the bottom of the desk stand. Guide the AC
wire along this channel; the wire will extend through an opening in the
back of the stand).
6. Plug the adaptor into a wall outlet.
NOTE: Only use the power adaptor (4.5VDC, 0.5A, 2.25W) supplied
with the kit.
CAUTION: The socket-outlet in which the direct plug-in adaptor is
inserted must be close to the keypad and easily accessible. The plug of
the adaptor serves as a means of disconnection from the supply mains.

Programming the Keypad

There are several programming options available for the keypad (see
below). Programming the keypad is similar to programming the rest of the
system. To turn an option on/off, press the number corresponding to the
option on the number pad. The numbers of the options that are currently
turned on will be displayed along the top of the LCD. For information on
programming the rest of your security system, please refer to your sys-
tem's Installation Manual.
Language Programming
1. Hold the [<][>] keys for 2 seconds to enter Language Programming.
2. Scroll to the desired language and press [,] to select.
3. Enter [,][8][Installer Code][,].
4. Enter [996][,] to reset custom labels to the selected language.
NOTE: If Section 075, Option 4 is turned off, language programming
can only be performed while in Installer's programming.
Plug
Wire
Channel