Technical Data - Grohe Red 40 409 Manual De Instrucciones

GB
Type approvals
The GROHE Red boiling water storage heater must be
installed with the safety assembly provided.
The boiling water storage heater may only be operated
together with an original GROHE Red boiling water fitting.
Safety notes
This device is not intended for use by persons
(including children) with physical, sensory or mental
impairments or a lack of experience or knowledge in
using devices of this type.
Children must be supervised to ensure that they do
not play with the device.
Prevent danger resulting from damaged power
supply cables. In the event of damage, the boiling
water storage heater must be replaced by the
manufacturer or its customer service department or
an equally qualified person.
• The boiling water storage heater must be connected to
a permanent power supply with earth wire.
• Installation is only possible in frost-free rooms.
• The boiling water storage heater is only suitable for
indoor use.
• The boiling water storage heater must be placed in an
upright position.
• The boiling water storage heater and plug must not be
directly or indirectly sprayed with water when cleaning.
• The boiling water storage heater must not be opened.
If the boiling water storage heater is to be drained (for any
reason), the safety assembly of the boiling water storage
heater must be removed. Invert the boiling water storage
heater and allow the water to run out.
However, we strongly advise against draining the boiling
water storage heater. There is a significant risk of
damaging the boiling water storage heater.

Technical data

• Connection:
• Voltage supply:
• Power consumption:
• Type of protection:
• Water connection at storage heater:
Fault
Water too cold
Flow rate too low
Storage valve losing
water
Wall socket with earth wire, protected
via a 16 A fuse
230 V AC / 50 Hz
Cause
• Empty storage heater switched on
('On' indicator lamp flashes)
• Heating phase not yet complete
• Isolating valve not fully open
• Water supply restricted
• Hose connection or internal tank leaking
Approval and conformity
This product conforms to the requirements of the
relevant EU guidelines.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica
Installation
Connect storage heater, see Figs. [1] - [3].
Do not connect voltage supply yet.
Filling storage heater with water, see Fig. [4].
1. Open shut-off valve (A1) at safety assembly (A), see detail,
Fig. [4].
2. Pull button (B1) on handle (B) of fitting outward and turn the
handle anti-clockwise.
3. Fill the storage heater until water comes out the spout of
the fitting.
4. Connect voltage supply via mains plug (C).
5. Press and hold button (D) on storage heater for at
least 2 seconds to switch on the storage heater. The red
indicator lamp (D1) indicates that the storage heater is
switched on.
The date of installation must be noted on the
maintenance sticker and affixed at a visible location
on the storage heater.
Service
Note the Fault/Cause/Remedy table for information on
eliminating problems.
If the problem cannot be rectified, disconnect the mains plug to
shut off the voltage supply. Note down the serial number of the
storage heater on the rear of the device and get in touch with
GROHE Customer Service or contact the GROHE Service
Hotline under TechnicalSupport-HQ@grohe.com.
Disposal
This category of devices does not belong in the
2100 W
domestic waste, but must be disposed of
IPX4
separately in accordance with the relevant local
Cold water national regulations.
Remedy
- Fill the storage heater, see section Installation
Reset the storage heater by pressing the reset
button (E) located on the rear of the storage heater
using a thin object, see Fig. [4]
- Wait max. 30 minutes
- Fully open shut-off valves, isolating valves
- Check supply lines, open isolating valve
- Switch off the storage heater, disconnect the mains
plug and contact GROHE Customer Service
2