LRP X100 OUTLAW 4.5T Manual De Instrucciones

USER MANUAL
X100 OUTLAW 4.5T
Dear customer,
thank you for your trust in this LRP product. By purchasing an LRP X100 Outlaw 4.5T,
you have chosen a highly efficient and powerful brushless motor. Developed for use
in hobby cars, the X100 Outlaw 4.5T guarantees high-speed driving enjoyment for a
reasonable price. IFMAR World Champion Technology for everyone!
Please read the following instructions carefully before you start using your motor. This
user guide contains important notes for the installation, the safety, the use and the
maintenance of this product. Thus protecting yourself and avoiding damages of the
product. Proceed according to the user guide in order to understand your motor better.
Please take your time as you will have much more joy with your product if you know
it exactly.
This user manual shall be kept in a safe place. If another customer is using this pro-
duct, this manual has to be handed over together with it.
1. Included in this package
X100 Outlaw 4.5T, User manual, Warning notes.
2. Installation & Connections
HALL-SENSOR WIRE: This bi-directional multipole wire, which is supplied with all LRP
sensored brushless speed controls, connects the speedo and the motor. Do not alter or
modify this cable! Make sure that the plugs have a proper and tight fit and are always
clean.
POWER WIRES: The unique splitted solder-tabs allow easy and convenient replace-
ment of the power wires. Nevertheless some soldering skills are required. Talk to your
local hobbyshop if you are concerned about soldering the wires yourself.
Caution: Avoid soldering longer than 5sec per soldering joint to prevent possible da-
mage to the motor due to overheating of the inner components!
• Install the motor in the model. Caution: The maximum length of the motor screws
shall not exceed 8mm.
• Connect the power wires
of the speed control and
+
C
the motor. Make sure that
the sequence is correct
by checking the color
code and the letters:
- MOT.A = blue wire
- MOT.B = yellow wire
- MOT.C = orange wire
• If you're using a sensored speed control, attach the hall-sensor wire to motor and
speedo now.
• Finally check all the connections before powering up the speed control.
3. PreciSensor System
The PreciSensor™ System allows precise control for best and most efficient perfor-
mance. The X100 Outlaw 4.5T already comes with optimal timing chosen by our en-
gineers. Therefore, it is ready to run out of the box, no additional timing adjustments
required.
Be careful when using aggressive advanced timing speed control profiles with X100
Outlaw 4.5T motors!
We recommend moderate usage of advanced timing speed control profiles with the
X100 Outlaw 4.5T. Such speed control timing profiles will increase motor temperatures
drastically and could lead to motor overheating or even failure. Therefore, please al-
ways monitor motor temperature in order to avoid damaging your motor.
4. Specifications
Order No. 50960
Voltage input [V] 4.8 - 11.1V
RPM 33'840
Specific
4700
RPM/V [kV]
Power [W] 850
Specifications subject to change without notice.
MA00254 © LRP electronic GmbH 2016
-
B A
Hall-Sensor wire
4.5T
Efficiency [%]
Weight [g]
Magnet material Sintered 13.0mm
Star (Multistrand
Winding
Copper Winding)
Sensor Compliant to world-
assignment wide racing rules
550 SIZE
SINTERED NEODYMIUM MAGNET
PRECISENSOR SYSTEM
5. Gearing Advice
A wrong gear-ratio causes excessive heating and may result in motor damage or ther-
mal shutdown of your speed control. Motor temperatures should be monitored, it
should never exceed 100°C (=212°F).
Please start with the smallest pinion and adjust accordingly until you find a good
compromise between temperature and performance!
6. Disassembly & Maintenance
Due to the maintenance free design of the X100 Outlaw 4.5T, it is not necessary to open
the motor frequently under normal conditions. It is just recommended to check that all
screws are still securely fastened.
Nevertheless it is recommended that you frequently maintain (clean, check, oil, replace
if needed!) the ball bearings in order to achieve best performance. Of course you can
also disassemble the motor entirely if you wish to do so.
Disassembly of the motor:
1. Loosen the center endcover screw and remove screw, plastic endcover and timing
insert.
2. Remove PreciSensor™ Assembly by pulling gently at sensor connector.
3. Loosen and remove the long/outer 3 screws and gently slide off the front aluminium
housing.
4. Remove the o-ring and shim from the shaft.
5. Carefully pull the rotor out of the housing and place it in a clean towel or designated
rotor container.
6. You have now access to both ball bearings for cleaning, maintenance and replace-
ment. You may also use compressed air to clean the inside of the motor after you
have removed the bearings.
Be careful with correct shim/o-ring position during re-assembly and avoid over-
tightening the screws!
7. Spare and Tuning Parts
For information about the latest spare and tuning parts, visit www.LRP .cc!
C
8. Repair Procedures / Limited Warranty
B
A
All products from LRP electronic GmbH (hereinafter called "LRP") are manufactured
according to the highest quality standards. LRP guarantees this product to be free from
defects in materials or workmanship for 90 days (non-european countris only) from the
original date of purchase verified by sales receipt. This limited warranty doesn´t cover
defects, which are a result of misuse, improper maintenance, outside interference or
mechanical damage. This applies among other things to:
• Overload (for example: unsoldered Star-ring)
• Excessive amounts of dirt inside the motor
• Rotor damage due to debris inside motor
• Mechanical damage due to external causes
• Rust
To eliminate all other possibilities or improper handling, first check all other compo-
nents in your model and the trouble shooting guide, if available, before you send in
this product for repair. If products are sent in for repair, which do operate perfectly, we
have to charge a service fee according to our pricelist.
With sending in this product, the customer has to advise LRP if the product should be
repaired in either case. If there is neither a warranty nor guarantee claim, the inspection
of the product and the repairs, if necessary, in either case will be charged with a fee at
the customers expense according to our price list. A proof of purchase including date
of purchase needs to be included. Otherwise, no warranty can be granted. For quick re-
pair- and return service, add your address and detailed description of the malfunction.
If LRP no longer manufactures a returned defective product and we are unable to
91
service it, we shall provide you with a product that has at least the same value from
one of the successor series.
240
The specifications like weight, size and others should be seen as guide values. Due to
ongoing technical improvements, which are done in the interest of the product, LRP
does not take any responsibility for the accuracy of these specs.
LRP-Distributor-Service: check www.lrp.cc
The crossed-out wheeled bin means that within the European Union the product must be taken to separate
collection at product end-of life. Do not dispose these products as unsorted municipal waste.
LRP electronic GmbH
Hanfwiesenstraße 15
73614 Schorndorf
Deutschland