2 3 Menu Item Edit Settings; Editing The Programming - Monacor PA-1200C Manual Del Usuario

F Relay status
After selecting the relay time delay, the display shows:
SET REL STATUS
ƊON
For the selected relays, the following options are
available:
1 . In the position , the selected relays remain en-
ON
ergized until a program step with the option
or a hold time is carried out set for the respective
relays . With a corresponding programming (see
chapter 5 .2 .6), the selected relays can also be
deactivated with one of the buttons CHIME A (2),
CHIME B (3), and CHIME C (4) .
2 . In the position
OFF
switched off .
3 . A hold time of 1 – 997 seconds can be adjusted
for the relays, i . e . the relays remain energized
for this time .
1) Adjust the desired setting with the button UP or
DOWN and confirm with ENTER . To set a hold
time for the relays, call up the submenu
. The display shows:
HOLD TIME
SET HOLD TIME
001S
2) Set the hold time with the button UP or DOWN
and confirm with the button ENTER . Then the
display shows:
HOLD TIME=xxxs
<PRESS ENTER>
Press the button ENTER again to confirm the
hold time . The submenu for the selection of an
announcement appears .
G Selecting an announcement
If the timer is operated with the digital message
insertion PA-1120DM, a stored announcement can
automatically be started after the chime .
1) After setting the hold time of the relay, the dis-
play shows:
SET MESSAGE
ƊMESSAGE 1
2) Select the number of the announcement storage
location with the button UP or DOWN .
3) If no announcement is planned for the pro-
grammed starting time, select the menu item
ƊNONE MESSAGE
4) Confirm the selection with the button ENTER .
Then the display shows:
MESSAGE=x
<PRESS ENTER>
Press the button ENTER again to confirm the
number . All settings are successively displayed
, the selected relays are
with the button DOWN .
once again . Then the submenu for storing the
programming appears .
H Storing the programming
1) After the complete programming was displayed,
the display changes to:
SAVE SETTINGS?
ƊYES
OFF
2) Either store the programming with the button
ENTER or, if it is not to be stored, switch to
with the button DOWN and then press the but-
ton ENTER .
3) If the programming was stored, the display shows
the storage location, e . g .:
MEM=1
<PRESS ENTER>
Press the button ENTER again to confirm the
number .
4) The menu for storing a new switching time ap-
pears again:
SET
MENU
ƊNEW SETTINGS
5) Repeat the programming for up to 40 switching
times . If all 40 storage locations are used, no
further switching time can be stored . The mes-
sage
NO FREE MEMORY
6) To exit the programming mode after storing a
switching time, select the menu item
the button DOWN and press the button ENTER .
Note: If the same starting time was accidentally stored
several times together with the same weekday, only the
program step with the lowest storage location number is
carried out . The programming should be changed .
5.2.3 Menu item

Editing the programming

Stored programmings can be changed under this
menu item .
1) Go to the menu item
the button UP or DOWN and to the first sub-
menu with the button ENTER . If no switching
times have been stored yet, the display shows
the message
2) If a switching time is stored, the display shows:
SELECT MEMORY
ƊMEM01
3) The first storage location with the corresponding
starting time is selected . To change this, press
the button ENTER . Otherwise, select the storage
location with the button UP or DOWN and then
press the button ENTER .
appears on the display .
EDIT SETTINGS
ƊEDIT SETTINGS
.
MEMORY EMPTY
[xx:xx]
ƊNO
with
ƊEXIT
with
15