Extended Functions; Basic Functions - Faber Symax GV60 Manual De Usuario

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

2.5

Setting the controls on the remote control unit.

2.5.1

Temperature/clock setting (fig 2.1.1)

The alteration of the temperature indication on the display screen

from °C/24hours to °F/12hours and the other way around is done

in the following manner:

•

Press the

key and the

indication is modified.

2.5.2

Time setting (fig 2.1.2)

•

Press the

and

key simultaneously, the day indication

will blink now.

•

Press the

key to set the number of the day.

(1=Monday, 2= Tuesday etc.).

•

Press the

and

key simultaneously, the hour indication

will blink now.

•

Press the

key to set the hour.

•

Press the

and

key simultaneously, the minutes

indication will blink now.

•

Press the

key to set the minutes.

•

To confirm press the

and

2.5.3

Setting the transmitter code on the remote

control unit

•

Press the reset button of the receiver with a pointed object

(fig. 1.2), until the second signal is audible. Now press the

key on the remote control unit, within 20 seconds. If a sound

signal is audible, the transmitter code has been set.

2.5.4

Setting the childproof lock (fig 2.1.3)

•

To activate the childproof lock press the

simultaneously.

is displayed and the handset is

rendered inoperable, except for the OFF function.

•

To deactivate the childproof lock press the

simultaneously.

disappears.

2.5.5

Setting one or two key ignition operation

The ignition operate can be set to one or two key operation.

Standard is one key operation.

•

To set this immediately press the

placing the batteries and wait until 1 or 2 flashes.

•

Release the key when the desired number flashes.

2.6

Basic functions

2.6.1 Switching on the fire (fig. 2.2.1 and 2.2.2)

One key operation

•

Press the

key until two short beeps and a blinking series

of lines appears. The fire automatically starts on high setting.

Fires, equiped with step burner, will start in the setting, in

which the fire the last time is switched off

Two key operation

•

Press the

and

key simultaneously until two short

beeps and a blinking series of lines appears.

The fire automatically starts on high setting.

Fires, equiped with step burner, will start in the setting,

in which the fire the last time is switched off

key simultaneously until the

key simultaneously.

and

key

and

key

key for 10 seconds after

2.6.2

Switching off the fire (fig 2.2.3)

•

Press the

key and the fire will be switched off completely.

2.6.3

Adjusting the flame height (fig 2.2.4, 2.2.5 and 2.2.6)

•

Keep the

key pressed to decrease the flame height step

by step or to switch back to pilot flame.

•

Pressing the

key twice in rapid succession will set the fire

to the lowest position.(LO appears in the display screen)

•

Keep the

key pressed to increase the flame height step

by step

•

Pressing the

key twice in rapid succession will set the fire

to the highest position. (HI appears in the display screen)

2.6.4

Switch the Step burner (fig.2.2.7)

NOTES:

Only for fires with step burner.

The step burner will not operate for 45 sec. after the start-up

procedure.

•

Press the

key until

the flame picture will concentrate in the middle of the burner.

•

Press the

key until

and the flame picture will divide over the complete length of

the burner.

2.6.5

Switch the LED Symbio effect (fig 2.2.8)

NOTES:

Only for fires with LED Symbio effect.

The Led Symbio module is independent of the flames and is

equipped with a standard light pattern.

•

Press the

key until

switch the effect on.

•

Press the

key until

switch the effect off.

2.7