Operation Instructions; Air Conditioner Use; Digital Controls; Important - Danby DAC10000 Guía A Utilizar Y Cuidar Del Proprietario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operating Instructions
AIR CONDITIONER
USE

DIGITAL CONTROLS

AIR CONDITIONER CONTROLS
The display always shows the room
temperature except when setting the
Set temperature or the delay timer.
Power
Auto
High
Med
Low
Fan
Speed
Power Pad
Turns air conditioner on and off. When turned on, the display will
show the room temperature.
Display
Shows the room temperature or time remaining on the Delay timer.
Shows the Set temperature while setting the temperature in Cool or
Energy Saver modes. The Set light will turn on while setting.
NOTE: The display will change to show the room temperature after
settings have been made. To change the Set temperature, press the
Temp increase
or decrease
Temp Increase
/ Decrease Pads
Use to set temperature when in Cool or Energy Saver mode.
The Set light will turn on while setting.
Delay Timer Increase
Each touch of the Increase / Decrease pads on the unit or the
Increase + / Decrease – pads on the remote control will set the delay
time when using the Delay 1–24hr timer (
on while setting.
Fan Speed Buttons
Use to set the fan speed to Low, Med, High or Auto on the unit.
NOTE: On the remote control, use the fan speed Increase + /
Decrease – pads to set the fan speeds to Low, Med or High. Use
the Auto pad to turn Auto fan on.
Operating your air conditioner properly helps you to obtain the
best possible results.
This section explains proper air conditioner operation.
If you turn off the air conditioner, wait at least 3 minutes before
turning it back on. This prevents the air conditioner from blowing a
fuse or tripping a circuit breaker.
Do not try to operate your air conditioner in the cooling mode when
outside temperature is below 65°F (18°C). The inside evaporator coil
will freeze up, and the air conditioner will operate properly.
NOTE: In the event of a power failure, your air conditioner will operate at
the previous settings when the power is restored.
Lights next to the touch pads on the air conditioner control panel
indicate the selected settings.
Light indicates the unit
is in the temperature or
delay time Set mode.
Set
Temp/Delay
Cool
Energy Saver
Fan only
Delay
Mode
1-24hr
Light indicates the
delay timer is set.
buttons
(+) /Decrease
(–) Pads
). The Set light will turn

IMPORTANT

REMOTE CONTROL
Delay 1–24hr
Delay timer
Decrease
Mode select
Fan speed
Decrease
Temperature
set Increase
and Decrease
Mode Button
Use to set the air conditioner to Cool, Energy Saver or Fan Only
mode.
Delay Buttons
Delay ON— When the air conditioner is off, it can be set to
automatically come on in 1 to 24 hours at its previous mode and
fan settings.
Delay OFF— When the air conditioner is on, it can be set to
automatically turn off in 1 to 24 hours.
How to set
Press the Delay 1–24hr pad on the unit or the (
remote control. Each touch of the Increase
on the unit or the Increase + / Decrease – pads on the remote
control will set the timer in 1-hour intervals. The Set light will turn on
while setting.
To review the remaining time on the Delay 1–24hr timer, press the
Delay 1–24hr pad on the unit or the (
control. Use the Increase
the Increase + / Decrease – pads on the remote control to set a new
time if desired.
During preview of timer or timer setting, press Delay 1-24hr button
on the panel or Delay button on the remote controller to cancel the
timer setting.
9
Delay timer
Increase.
Auto Fan on
Fan speed
Increase
Unit power
on/off
) pad on the
/ Decrease
) pad on the remote
/ Decrease
pads on the unit or
pads

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dac12011

Tabla de contenido