Digital Display - Energy Plus CE163TW Manual De Usuario

WARNING: HEATER MUST BE PROPERLY INSTALLED BEFORE IT IS ENERGIZED OR OPERATED.
Fan Mode
Indicator
Temperature
Heating Mode
Indicator
Heater Modes
Using the rocker switch, you can move the switch to
three modes.
HEAT
CENTER POSITION: NO HEAT MODE
After a brief cool down period (up to 4 minutes), the heater
will shut down. It will not resume heating until the rocker
switch is flipped to the HEATING (left) position.
No Heat, Cool Down
LEFT POSITION: HEAT MODE
Your ComPak Energy Plus heater has a unique variable speed
blower that auto adjusts the heat output based on the room's
requirements. Once you set the thermostat to your desired
temperature, the heater will vary the wattage output for
maximum efficiency.
The digital display will show the level of heat being output to
maintain the room's temperature.
Heating Full Power
RIGHT POSITION: FAN ONLY MODE
The FAN ONLY mode can circulate air but will not supply heat.
Three fan speeds are available. To adjust the fan speed: With
rocker switch in the RIGHT position, push top (+) or bottom (-)
digital buttons up or down. Display will read "1" for low speed,
"2" for medium speed, or "3" for high speed during the set up
process, then resume to temperature display.
6
OPERATINg YOUR HEATER

Digital Display

NO HEAT
FAN
ONLY
Rocker Switch
fan is
animated
No Heat
Heating Mid Power Heating Low Power
Fan Only / No Heat
Fan Operation
Fahrenheit Setting
Night/Away Mode Icon
Digital Display
Proportional Heat Rocker Switch
Control Indicator
Setting Desired
Heating Temperature
Turn rocker switch to HEAT mode.
•
Touch the up
•
button to set your desired temperature.
Temperature Setpoint Range: 40˚F - 90˚F
Program Your Night/Away Button
You can preset a night or away temperature set point, for quick
and easy "one-touch" energy savings.
Turn rocker switch to HEAT mode.
•
• Push Night
The moon icon will show in display
screen. The "night/away" setpoint
temperature will flash for 5 seconds.
Push the Up
•
change your desired night/away set point.
• To return to your previous HEAT set point
when you awake or return, push the
Night
will flash for 5 seconds. The moon icon
will no longer be in display screen.
To return to your previous night/away
•
setpoint, simply push the Night
Max/Min Temperature Lock
You can preset a maximum and/or minimum set point as a child
safety or tamper proof option. To preset a maximum setpoint:
Move rocker switch to NO HEAT mode.
•
• Press and hold both the Night
at the same time, for at least 5 seconds, until the "HL" (high limit)
is displayed.
• Release buttons: temperature setpoint will flash and alternate
with "HL" on the display.
Using the Up
•
set point.
Turn rocker switch back to HEAT mode.
•
To remove the lock, follow same instructions, and set to
•
maximum of 90 degrees.
To preset a minimum set point, follow same steps, but press
•
and hold both the Night
(low limit) is displayed.
Energy Saving Tips
Set your Night/Away
•
comfortable, for a cooler nighttime temperature.
• When you exit the room or leave your home, push the
Night
If your heater is positioned in a drafty area or exposed to direct
•
sunlight, temperature reading will be affected. Set temperature
to desired comfort level, not a "number" on the digital display.
If you will be away for an extended period of time (and have
•
no concerns about freezing conditions), turn the rocker switch
to NO HEAT for even greater energy savings.
Control Buttons
Up Button
+
NO
F
NO
Down Button HEAT T
Night Button
NO FAN
SLEEP
NO HEAT
FAN
HEAT
ONLY
button or the down
button to activate.
or Down button to
again. The setpoint temperature
button.
button and the Up
or Down button, set your maximum desired
and Down
set point to as low as you are
button to drop the temperature set point.
up
down
NIGHT/
AWAY
Night/Away Button
Night/Away Mode
button
buttons until the "LL"