Front Panel - Rane ONE Guia Del Usuario

41. Loop On/Off / Reloop: Press this button to create an auto-loop with the length that is set in
the software.
Press and hold Shift and then press this button to skip to the last-played loop and activate it
immediately.
Note: Roll sizes will affect loop sizes in the software and loop based on the last roll size.
42. Loop In / x1/2: Press this button to create a Loop In point at the current location.
Press and hold Shift and press this button to halve the length of the current loop.
43. Loop Out / x2: Press this button to create a Loop Out point at the current location.
Press and hold Shift and press this button to double the length of the current loop.

Front Panel

2
3
1
1. Mic 1 – Off/On: When set to Off, the Mic 1 Input is disabled. When set to On, the Mic 1 Input on
the rear panel is active, and its audio signal is routed directly to the program mix and cue mix.
2. Mic 1 Level: Turn this knob to adjust the gain of the Mic 1 Input.
3. Mic 1 Tone: Turn this knob to adjust the balance of low (bass) and high (treble) frequencies of
the audio signal coming from the Mic 1 Input.
4. Mic 2 – Aux/Off/Mic 2: When set to Aux, the Aux In on the rear panel is active. When set to
Off, the Aux Input and Mic 2 Input are both disabled. When set to Mic 2, the Mic 2 Input on
the rear panel is active, and its audio signal is routed directly to the program mix and cue mix.
Both audio signals are routed directly to the program mix and cue mix when active.
5. Mic 2 / Aux Level: Turn this knob to adjust the gain of the Mic 2 Input or AUX Input.
6. Mic 2 / Aux Tone: Turn this knob to adjust the balance of low (bass) and high (treble)
frequencies of the audio signal coming from the Mic 2 Input or AUX Input.
7. Deck Reverse: Set this switch to On to reverse the direction of the deck faders. Set it to Off to
use the conventional fader direction.
8. Deck Contour: Adjusts the slope of the deck fader curve. Turn the knob to the left for a
smooth fade (mixing) or to the right for a sharp cut (scratching). The center position is a typical
setting for club performances.
9. Crossfader Contour: Adjusts the slope of the crossfader curve. Turn the knob to the left for a
smooth fade (mixing) or to the right for a sharp cut (scratching). The center position is a typical
setting for club performances.
10. Crossfader Reverse: Set this switch to On to reverse the direction of the crossfader. Set it to
Off to use the conventional fader direction.
11. Cue Mix: Turn to mix between the cue channel and program mix in the headphone outputs.
When all the way to the left, only the cue channel will be heard. When all the way to the right,
only the program mix will be heard.
12. Cue Split: When this switch is in the On position, the headphone audio will be "split" such that
the cue channel are summed to mono and sent to the left headphone channel while the
program mix is summed to mono and sent to the right channel. When the switch is in the Off
position, the cue channel and program mix will be "blended" together. In both cases, use the
Cue Mix knob to control the blend of the two signals.
13. Cue Level: Turn this knob to adjust the volume level of the cue channel.
14. Headphone Outputs (1/4", 1/8" / 6.35 mm, 3.5 mm, TRS): Connect your 1/4" or 1/8" (6.35 mm
or 3.5 mm) headphones to this output for cueing and mix monitoring.
8
5
6
4
8
9
7 7
11 13
12
10
14