Important Safety Advice - Clemas & Co Cimex R48HD Manual De Instrucciones

1
Motor switch lever
When raised switches
motor ON and starts the
rotating heads, when
released switches motor
OFF and stops the heads.
Each time the lever is
operated the direction of
head rotation is reversed,
improving the quality of
cleaning 7
and prolonging disc/pad
life.
Handle
2
Clamping bar
3
Drive pins
4
Rotating heads
5
1. Product information
This heavy duty three brush floor cleaning machine is
suitable for heavy duty commercial use. Ideal for floor
preparation; removing impacted grease, oil and debris
from concrete floors; removing build-up of ice in cold
store floors; and glue, carpet backing foam and rubber
removal. The machine is intended for commercial use,
for example in hotels, schools, hospitals, factories,
shops, offices, rental businesses and other than normal
housekeeping purposes.
The following instructions contain important information
about the machines and safety advice for the operator.
These instructions are valid for the following models:
Cimex HD - R48HD...
Equipment must be operated, serviced and maintained
in accordance with the manufacturer's instructions. If in
doubt contact the supplier of your machine.

1.1 Important safety advice

When using this machine, basic safety
precautions should be followed, including the
following:
• This
machine must
manufacturer's approved application as described in
this manual.
• Please note that the safety information described in
the manual supplements and does not replace
standards in force in the country in which the machine
is used.
• WARNING - Only use accessories and spare parts
provided with the machine or those approved by the
6
Handle adjustment
lever
From the upright
position, lift the
handle adjustment
lever and pull the
handle backwards to
a comfortable working
height, then press
lever down to lock
handle in position
Cable hooks Used to
hold supply cord in
place on handle when
machines not in use
Drive plates
8
Attachment point for
brushes or drive discs
and pads
Rotating dust cover
9
only be used for
manufacturer. The use of other spare parts or
accessories may impair the safety of the machine.
• CAUTION - This machine is for dry indoor use only
and should not be used or stored outdoors in wet
conditions.
• All parts are to be positioned as indicated in the
instructions before using the machine.
• The machine must be unpacked and assembled in
accordance with these instructions before connecting
to the electrical supply.
• DO NOT use where hazardous dust is present.
• DO NOT use in an explosive atmosphere.
• DO NOT pick up or use near flammable fluids, dusts
or vapours.
• DO NOT use to clean up any burning or lighted
materials such as cigarettes, matches, ashes or other
combustible objects.
• Take care when using a machine near the top of stairs
to avoid overbalancing.
• Only use the machine on firm level surfaces. DO NOT
use on a gradient or more than 2% slopes.
• DO NOT use diesel/petrol or corrosive detergents to
wash floors.
• DO NOT wash and vacuum corrosive, flammable and/
or explosive liquids, even if diluted.
• DO NOT put any object into openings. DO NOT use
with any opening blocked; keep free of dust, debris
and anything that may reduce airflow.
• DO NOT cover machine when in use.
• DO NOT leave the machine connected to the
electricity supply when not in use; always remove the
plug from the socket outlet.
• DO NOT leave machine running unattended.
• This machine should always be connected to a fully
earthed power supply of the right voltage and
frequency. • The machine shall be disconnected from
its power source during its cleaning or maintenance
and when replacing parts or accessories, by removing
the plug from the socket-outlet.
• DO NOT use if it has been damaged, left outdoors or
dropped into water.
• DO NOT operate switches or touch the mains plug
with wet hands as this may cause electric shock.
• WARNING - Keep the power supply cord clear of
moving parts (and/or rotating brushes). During
operation hazard may occur when running the
machine over the power supply cord.
• DO NOT operate the machine with a damaged supply
cord or plug, or after the machine malfunctions or is
damaged in any way. Contact an authorised Service
Agent for repair or adjustment.
• DO NOT pull or carry by the supply cord. DO NOT use
cord as a handle, close door on cord or pull cord
the
around sharp edges or corners.
• The plug of the power supply cord must be removed
from the socket-outlet before commencing cleaning of
the machine or undertaking maintenance operations.
• DO NOT kink or twist the power cord and keep cord
• When unplugging, pull the plug, not the supply cord.
4