Rokonet Prosound RS200WAP000A Manual De Instalación página 6

Terminal Description
TAMPER R
q~ãéÉê=çìíéìíë=Ñçê=Et~ää=~åÇ=ÅçîÉê=í~ãéÉêáåÖFK=qÜÉ=ÅçååÉÅíáçå=çÑ=íÜÉëÉ=
íÉêãáå~äë=ÇÉéÉåÇë=çå=íÜÉ=ëÉííáåÖ=çÑ=íÜÉ=q^jmbo=àìãéÉêW=
TAMPER F
INTW=`çååÉÅí=íÜÉ=c=íç=íÜÉ=`lj=Ekç=ÅçååÉÅíáçå=íç=o=íÉêãáå~äFK=
EXTW=`çååÉÅí=íÜÉ=o=~åÇ=íÜÉ=c=íç=~=òçåÉ=áåéìíK=
1 PIN OnlyW=`çååÉÅí=íÜÉ=o=~åÇ=íÜÉ=c=íç=~=òçåÉ=áåéìí=bliK=E^å=áåíÉêå~ä=OKO=h=
bli=êÉëáëíçê=áë=ÅçååÉÅíÉÇ=áå=ëÉêá~ä=íç=íÜÉ=çìíéìíF =
PROX
`çååÉÅí=íÜÉëÉ=íÉêãáå~äë=íç=~=òçåÉ=áåéìí=Ñçê=íÜÉ=áåÇáÅ~íáçå=çÑ=^åíá=~ééêç~ÅÜ=
(N.C)
~ä~êãK=Epí~åÇ=^äçåÉ=ãçÇÉ=çåäóF=
NOTE:
You can connect the PROX terminals in serial to the TAMPER terminals in order to have
a single tamper indication from the sounder.
TRBL
qÜÉ=íêçìÄäÉ=çìíéìí=áë=~Åíáî~íÉÇ=EÅäçëÉÇF=~ÅÅçêÇáåÖ=íç=~=íêçìÄäÉ=ÇÉÑáåÉÇ=Äó=íÜÉ=
ëÉííáåÖ=çÑ=íÜÉ=íêçìÄäÉ=ÇáéJëïáíÅÜ=E`lkcfd=NFK=
(N.O)
C+
qÉêãáå~ä=íç=éçëáíáîÉX=ëçìåÇÉê=áë=ëáäÉåíK==
qÉêãáå~ä=çéÉåI=ëçìåÇÉê=áë=~Åíáî~íÉÇK=
C-
qÉêãáå~ä=íç=åÉÖ~íáîÉX=ëçìåÇÉê=áë=ëáäÉåíK==
qÉêãáå~ä=çéÉåI=ëçìåÇÉê=áë=~Åíáî~íÉÇ=
ST
qÉêãáå~ä=íç=åÉÖ~íáîÉI=ëíêçÄÉ=áë=~Åíáî~íÉÇK==
qÉêãáå~ä=çéÉåI=ëíêçÄÉ=áë=ÇÉ~Åíáî~íÉÇK=
NOTES:
1. The sounder will not operate when a battery is not connected or no power supply is connected to the
PS terminals.
2. After powering-up the sounder, it will not operate for a period of 20 seconds (sound and strobe) in
order to avoid accidental activation during installation.
3. After powering-up the sounder, the sounder inputs (C- or C+) will cause activation only if they have
been in normal (silent) state at least for 10 seconds
4. The PROX and TRBL outputs are deactivated in BUS mode configuration.
5. To protect the battery against deep discharge, the battery will be automatically disconnected below
10.5 VDC
Tam per O utput
(0.5A, 24V N.C)
Anti Approach
Output
(0.1A, 24V N.C)
Trouble O utput
70 m A m ax
+ 12 V
CO M (-)
CO M (-)
=
=
=
Optional
To
13.8VDC
Battery
1.6 A
TA M P E R
B LK
IN T E X T
(To Int.
Tam per)
TR IG S TR O B
PO W ER
C - A U TO
C + M A N
O N
O N
1
1 2 3 4
ID1
CO NFIG
LED2
Figure 1 – Stand Alone Configuration
S=
R E D
2 3 4
To Internal
Speaker
13.8VDC ,
200 m A (m ax)
Status LED2
O n/O ff