Denon DN-C635 Instrucciones De Operación página 7

!6
Pitch Slider
• Use this slider to adjust the play speed. Slide
up to decrease the play speed, down to
increase the play speed.
!7
PROG. PLAY ON/OFF button
• When this button is pressed while the PROG
indicator is lit, the program play mode is set.
• The button will not function during the A-B play
mode.
• The PROG. PLAY ON/OFF LED lights during
the program play standby and play modes.
• When the button is pressed during the
program play standby or play mode, the
program play mode is cleared.
!8
PROGRAM IN button
• Press this button to set the program input
mode.
• The button will not function during the play
mode.
• The PROG indicator flashes when in the
program input mode.
• The PROG indicator lights when a program is
set.
!9
REPEAT button
• Press this to perform repeat playback.
@0
TIME button
• The time display switches each time this
button is pressed. ("REMAIN", "ELAPSED")
@1
TITLE button
• When the button is pressed, the text
information (Disc title, track title, disc artist or
track artits) is displayed.
• When the button is pressed while in the stop
mode with a disc containing an MP3 ID3-Tag
loaded, the file name is displayed.
pressed during playback, the display switches
as shown below.
Elapsed time of currently playing track
File name of currently playing track
Title name
Artist name
Album name
@2
FOLDER button
• When disc containing MP3 format files is
loaded, in the stop mode press this button then
the folder select mode is possible.
@3
A-B (A-B repeat) button
• Use this to play a set section repeatedly.
• When the button is pressed once during
playback, that position is set as the A point and
the "A-B" indicator flashes on the display.
• When the button is pressed again, that position
is set as the B point, the "A-B" indicator stops
flashing (remaining lit), and the A-B section
begins playing repeatedly.
• When the button is pressed again, A-B repeat
is canceled and the mode returns to the normal
play mode.
@4
Headphones jack
• For private listening, you can connect your
headphones to this jack.
@5
PHONES LEVEL control
• Use this adjust the output level of the
headphones.
When
(2) Rear panel
q
BALANCED OUT connectors
• These are active balanced outputs using XLR
type connections. The CD's playback signals
are output from these connectors.
• Pin layout : 1. Common / 2. Hot / 3. Cold
• Applicable connector :
Cannon XLR-3-31 or equivalent.
NOTE :
• Do not short-circuit the hot or cold pin with
the common pin.
w
LEVEL L/R controls
• Use these controls to adjust the level of the
audio signals from the BALANCED OUT
connectors.
e
UNBALANCED OUT jacks
• These are unbalanced outputs using RCA type
jacks.
r
DIGITAL OUT jack
• This is a coaxial output using an RCA type jack.
II
• Signal format : SPDIF or IEC-958 Type
t
Serial control port
• This is serial remote connector.
• Applicable connector : 9-pin D-sub (male)
• Baud rate : 9600 bps
• Pin layout
RS-232C
Pin No. Signal Name I / O
1 GND
6 NC
2 TxD
7 NC
3 RxD
8 NC
4 NC
9 NC
5 S. GROUND
RS-422A
Pin No. Signal Name
1 GND
6 NC
2 TxD (RETURN)
7 TxD
3 RxD
8 RxD (RETURN)
4 NC
9 NC
5 S. GROUND
y
Parallel remote control port
• This is a parallel remote connector.
• Applicable connector : 25-pin D-sub (male)
• Connecting signal layout
Pin No. Signal Name I / O
_
1 FG
14 PLAY tally O TTL (Iol = 20mA)
2 PLAY command I HCMOS (Ii = 3mA)
15 PAUSE tally O TTL (Iol = 20mA)
3 PAUSE command I HCMOS (Ii = 3mA)
16 CUE tally O TTL (Iol = 20mA)
4 CUE command I HCMOS (Ii = 3mA)
17 INDEX 2/INDEX 3 tally O TTL (Iol = 20mA)
5 TRACK (+) command I HCMOS (Ii = 3mA)
_
18 Tally common
_
6 TRACK (–) command I HCMOS (Ii = 3mA)
_
_
19 Reserved
O
7 SEARCH (Fwd) command I HCMOS (Ii = 3mA)
_
_
20 Reserved
I
8 SEARCH (Rev) command I HCMOS (Ii = 3mA)
_
_
21 Reserved
_
9 FADER START command I HCMOS (Ii = 3mA)
_
_
22 Tally power supply +3.3V, 20mA
_
_
10 Command common (Ii = 10mA)
_
23 Command common
_
11 NC
_
24 EOM tally TTL (Iol = 20mA)
_
12 Reserved
_
25 Reserved
_
13 Reserved
ENGLISH
I / O
_
_
O
O
I
I
_
_
_
7