Safety Battery And Charge Information - ATEQ Orange Electronic OE46 Guia Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

5. SAFETY BATTERY AND CHARGE
INFORMATION
You must read and understand these
safety instructions and warnings before
using or charging your Lithium-Polymer
batteries.
Operating environment
Remember to follow any special current
regulations in any area, and always switch off
your device when its use is prohibited or
when it may cause interference or danger.
Use the device only in its normal operating
positions.
Your device and its enhancements may
contain small parts. Keep them out of the
reach of small children.
About Charging
Only use the charger supplied with your
device. Using another type of charger will
result in malfunction and/or danger.
When the red LED turns off, the charge is
complete.
About the Charger
Do not use the charger in a high moisture
environment. Never touch the charger when
your hands or feet are wet.
Allow ventilation around the charger when
using it. Do not cover the charger with paper
or other objects that will reduce cooling. Do
not use the charger while it is inside a
carrying case.
Connect the charger to a proper power
source. The voltage requirements are found
on the product case and/or packaging.
Do not use the charger if the wires become
damaged. Do not attempt to service the unit.
There are no serviceable parts inside.
Replace the unit if it is damaged or exposed
to excess moisture.
This charger is not a toy and should not be
used by children or infirm persons without
proper training or supervision.
Do not use it as a power source.
Unplug the charger before attempting to
service or clean it.
UM-365OEA-U
OE46 TPMS TOOL User Guide
About the Battery
CAUTION: This unit contains an internal
Lithium-Polymer battery. The battery can
burst
or
explode,
chemicals. To reduce the risk of fire or burns,
do not disassemble, crush, pierce or dispose
of the battery or the instrument in fire or
water, do not short circuit or short the
contacts with a metal object.
Use a specified charger approved by Orange
Electronic and supplied with the device.
The tool must be returned to the factory for
battery replacement.
Opening the tool or tampering with the
seal placed on the tool, if broken, will void
the warranty.
Safety for Lithium-Polymer battery use
NEVER leave the battery unattended during
the charging process. The device must
imperatively be placed on a non-flammable
surface during charging (ceramic platter or
metal box).
Charge the Lithium-Polymer battery ONLY
with the charger provided.
NEVER use a Ni-MH (Nickel Metal Hydride)
type battery charger to charge a Lithium-
Polymer battery.
If the battery begins to overheat more than
60°C
(140°F),
IMMEDIATELY. The battery should NEVER
exceed 60°C (140°F) during the charging
process.
NEVER charge the battery immediately after
use and while still hot. Leave it to cool down
to ambient temperature.
If you see any smoke or liquid coming from
the battery, stop the charge immediately.
Disconnect the charger and place the tool in
an isolated area for at least 15 minutes. DO
NOT USE THE BATTERY AGAIN. Return
the device to your retailer.
Keep a fire extinguisher for electrical fires
handy while charging the battery. In the
unlikely
event
that
battery catches fire, DO NOT use water to
extinguish the fire. Take some sand or use a
fire extinguisher as described above.
The Lithium-Polymer battery elements must
be neutralized to be made unusable. The
neutralization process must be performed
under
strict
safety
recommended that you return the tool to us.
User manual OE46 Page 31/34
releasing
hazardous
STOP
CHARGING
the
Lithium-Polymer
conditions.
It
is

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Jorg2-07

Tabla de contenido