System Option Settings Menu - Legacy ProLine Serie Instrucciones De Operación

LEGACY 3215/3245메뉴얼 03.3.3 8:39 PM 페이지9
To set the two-tone option, press the MODE button then the C C H H S S E E T T up or down buttons until the display
appears. Press and release the MODE button again to select. Scroll through the sub-menu settings with
the up or down buttons, press the MODE button when T T W W O O T T O O N N E E appears on screen. Settings include:
I I N N D D I I V V I I D D
G G R R O O U U P P
S S U U P P E E R R G G R R
between these settings with the up or down buttons. When the desired setting appears on screen, press
the MODE button to select. Next, toggle between On and Off status settings which occur for each
above sub-menu.
Example: I I N N D D I I V V E E O O N N , G G R R O O U U P P O O F F and S S G G R R P P O O N N .
9
When the desired setting appears on screen, press the MODE button to select. The radio will save your
On or Off selection for the current channel and return to standby mode. NOTE: Individual, Group and
Super Group frequencies and timing are programmed by your radio communications Dealer.
For quick reference, the next few pages detail the Channel Options Menu, sub-menus and their settings.
Mode Option Setting Each Channel Setting
System Option Setting
Display Option Setting
Channel Option Setting Tone Option
Tx Output Power High/Low
Normal Scan List
2-Tone Option
You can toggle
RX Tone No Tone
CTCSS 1-49
DCS 023-754
Invert DCS 023-754
TX Tone No Tone
CTCSS 1-49
DCS 023-754
Invert DCS 023-754
Power High/Low
Normal Scan On/Off
Priority Scan List Priority Scan On/Off
Individual Tone On/Off
Group tone
On/Off
Super Group Tone On/Off

System Option Settings Menu

To enter the System Option Setting Menu, press and release the MODE button during the receive or
standby mode, then use the up or down buttons until S S Y Y S S T T E E M M appears. Select the above option with a
press and release of the MODE button.
(Beep Set, VOX (Voice Operated TX) Set, Time-Out-Timer Set, Penalty, Busy Channel Lockout Set,
Marked Idle, Scan Set, Priority Scan, Transmit Delay, Power Save, Clear-To-Talk, Roger Beep, 2 tone
alarm, Microphone Hook and Audio Compander). Details on sub-menu settings follow.
You can toggle between these settings with the up or down buttons. When the desired setting appears
on screen, press the MODE button to select. If you choose the Beep Set setting, you will need to use the
up or down buttons to choose B B E E E E P P O O N N or B B E E E E P P O O F F . When the desired setting appears on screen, press the
MODE button to select. The radio will save your On or Off selection and return to standby mode.
If you choose the VOX Set setting, you will also need to choose between On or Off selections, by using
the up or down buttons to choose, and the MODE button to select. If you choose On, you will need to
choose a VOX level setting, which includes: V V O O X X L L L L 1 1 , , V V O O X X L L L L 2 2 or V V O O X X L L L L 3 3 . You can toggle between these
VOX sensitivity level settings with the up or down buttons. When the desired setting appears on screen,
press the MODE button. The radio will save your selection and return to standby mode.
If you choose the Time-Out-Timer setting, your choices include: T T O O T T O O N N or T T O O T T O O F F . Toggle between
the settings with the up or down buttons. When the desired setting appears on screen, press the MODE
button. If you choose "On", you will need to choose the duration of the Time-Out-Timer setting, from 10
seconds to 990 seconds. Use the up or down buttons to toggle, until the desired number of seconds
appears on the display. Use the MODE button to select. The radio will save your selection and return to
standby mode. Example of display: T T O O T T 9 9 9 9 0 0
NOTE: In the Time-Out-Timer sub-menu, if "Off" is selected by pressing the MODE button, the TOT
function will be disabled, and the radio will return to standby mode.
If you choose the Time-Out-Timer Penalty setting, your choices include Penalty On or Off. Toggle
between the settings with the up or down buttons. When the desired setting appears on screen, press the
MODE button. If you choose "On", you will need to choose the duration of the Penalty setting, from 1
second to 100 seconds. Use the up or down buttons to toggle, then the MODE button to select the
desired amount of time. The radio will save your selection and return to standby mode.
Example of display: P P N N L L T T 1 1 0 0 0 0 .
NOTE: In the Time-Out-Timer Penalty sub-menu, if "Off" is selected by pressing the MODE button, the
TOT Penalty function will be disabled, and the radio will return to standby mode.
NOTE: If the radio transmits in excess of the set time, it will beep an error tone and the radio will receive a
signal, but will NOT transmit during the penalty time.
If you choose the Busy Channel Lockout setting, your choices include: B B C C L L O O O O N N or B B C C L L O O O O F F . Toggle
between the settings with the up or down buttons. When the desired setting appears on screen, press the
MODE button. Your radio will save your On or Off selection and return to standby mode.
NOTE: If you select "On", and the channel is busy, it will inhibit transmission.
If you choose the Marked Idle setting, your choices include On or Off. Toggle between the settings with
the up or down buttons. When the desired setting appears on screen, press the MODE button to select.
The radio will save your selection and return to standby mode.
Example of display: M M A A R R K K O O N N .
NOTE: If the channel is set by Busy Channel Lockout, and transmit is inhibited, Marked Idle allows a
transmission when your CTCSS or DCS tone signal is received.
10