Connecting To The Resolv120A Subwoofer - Samson Audio RESOLV 65a Manual Del Usuario

Resolv 65a with Mono Sub
Adding a subwoofer and extended low frequency response to your Resolv 65a system is easy using the
RESOLV 65a's LINE LEVEL inputs. Below is a typical system set-up using the RESOLV 120a with a mixer and a
pair of Resolv 65a's satellite speakers. The RESOLV 65a's inputs utilize industry standard RCA connectors. For
a detailed wiring diagram, see the section "RESOLV 65a Connections" on page 12. Follow the steps in the dia-
gram below to set up your system.
FROM MIXER
• Lower your mixer's master outputs to all the way off.
• Connect the mixer's left output to the RESOLV 120's LEFT LINE INPUT and the mixer's right output to
the RESOLV 120's RIGHT LINE INPUT. Now connect the RESOLV 120's LEFT LINE OUTPUT to the input of
the left RESOLV 65a, and the RESOLV 120's RIGHT LINE OUTPUT to the input of the right RESOLV 65a.
• Run an audio signal (like some music from a CD) through your mixer and raise the level to a
fortable listening level.
• Now adjust the SWEEP control to the desired frequency. Consult your studio monitors owner's man-
ual for a recommended crossover point. You can also use your ears by adjusting the SWEEP control to
the frequency that sounds good to you. A good place to start is about 70 Hz.

Connecting to the Resolv120a Subwoofer

5
0
-9
dBr
-15
-21 mSec
-27
10 100 1K 10K 30K
CROSSOVER FREQUENCY (Hz) 100.0 100. 1000.0 1000. 10000.0 10000. SPECTRAL DECAY SPECTRAL DECAY SPECTRAL DECA
50
30
+6
+3 0
dBr
0
-15
-3
-6 -30
500 1K 2K 5K
-50
10 100 1K 10K 30K
MID PRESENCE FREQUENCY (Hz) FREQUENCY RESPONSE FREQUENCY (Hz)
0dB +3dB
+6dB ACTIVE MONITOR
-3dB POWER
SPECS:
•20Hz - 20kHz
•BIAMPED 75 WATT WATT WA WOOFER
MID PRESENCE
COPOLYMEP C POL POLYMEP C ONE
•25 WATT WA WATT TIT TITANIUM FERRO TITANIUM FERRO
ON
FLUID TWEETER
AUDIO
•TIME ALIGNED WAVEGUIDE WAVEGUIDE WA
INPUTS
•MAGNETICALLY SHIELDED NETICALL NETICALLY SHIELDED
OFF
WARNING:
RESOLV MONIT LV MONIT LV ORS CAN ACHIEVE
EXTREMELY HIGH SOUND PRESSURE EXTREMELY HIGH SOUND PRESSURE EXTREMEL
0 10
VOLUME LEVELS. USE CA LEVELS. LEVELS. USE CA UTION OR HEARING
DAMAGE MAY RESU GE MA GE MAY RESU LT
LINE
S/N
POWER
RATING 115-230 vac — 50Hz/60Hz 175W
CAUTION
BALANCED RISK OF ELECTRIC SHOCK
DO NOT OPEN
www.samsontech.com
DESIGNED AND ENGINEERED IN THE UNITED ST ES BY SAMSON TECHNOLOGIES DESIGNED AND ENGINEERED IN THE UNITED STAT DESIGNED AND ENGINEERED IN THE UNITED STAT MADE IN CHINA
5
0
-9
dBr
-15
-21
-27
10 100 1K 10K 30K
CROSSOVER FREQUENCY (Hz)
+6
+3
0
-3
-6
500 1K 2K 5K
MID PRESENCE FREQUENCY (Hz) FREQUENCY RESPONSE
0dB +3dB
+6dB ACTIVE MONITOR
-3dB
SPECS:
•20Hz - 20kHz
•BIAMPED 75 WATT WA WATT
MID PRESENCE
COPOLYMEP CONE
•25 WATT WATT WA TIT TITANIUM FERRO TITANIUM FERRO
FLUID TWEETER
AUDIO
•TIME ALIGNED WAVEGUIDE WAVEGUIDE WA
INPUTS
•MAGNETICALLY SHIELDED GNETICALLY SHIELDED GNETICALL
WARNING:
RESOLV MONIT LV MONIT LV ORS CAN ACHIEVE
EXTREMELY HIGH SOUND PRESSURE EXTREMELY HIGH SOUND PRESSURE EXTREMEL
0 10
VOLUME LEVELS. USE CA LEVELS. LEVELS. USE CA UTION OR HEARING
DAMAGE MAY RESU E MAY RESU E MA
LINE
S/N
POWER
RATING 115-230 vac — 50Hz/60Hz 175W
CAUTION
BALANCED RISK OF ELECTRIC SHOCK
DO NOT OPEN
www.samsontech.com
DESIGNED AND ENGINEERED IN THE UNITED STAT DESIGNED AND ENGINEERED IN THE UNITED STAT DESIGNED AND ENGINEERED IN THE UNITED ST ES BY SAMSON TECHNOLOGIES
10 Inch Long Throw Transducer 120 Watt Amplifier
11
0.00
0.79
1.63
2.43 mSec
100.0 100. 1000.0 1000.0 10000.0 10000.0 SPECTRAL DECA SPECTRAL DECAY SPECTRAL DECAY
50
30
0
dBr
-15
-30
-50
10 100 1K 10K 30K
FREQUENCY (Hz)
POWER
WOOFER
ON
OFF
LT
MADE IN CHINA
com-