Tabla de contenido
Publicidad
Enlaces rápidos
Installation Manual
By Firstech LLC, Version: 1.0
Applicable to the following alarm system:
CM-2300 – Alarm/Keyless Control Module
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions;
(1) This device may not cause harmful interference.
(2) This device may accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this device.
techfeed.compustar.com
Publicidad
Tabla de contenido
Resumen de contenidos para Firstech CM-2300
- Página 1 By Firstech LLC, Version: 1.0 Applicable to the following alarm system: CM-2300 – Alarm/Keyless Control Module This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions; (1) This device may not cause harmful interference.
-
Página 2: Tabla De Contenido
This is not a tutorial on Installation Basics ............................4 how to install. We highly recommend that you contact your local Firstech dealer and seek professional how to install. We highly recommend that you contact your local Firstech dealer and seek professional Remote Code Routine(s) ..........................5... -
Página 3: Installation Basics
Antenna The antenna on the CM-2300 is internal and wired directly to the control module. There is no need to run a cable up the A pillar unless you are using a different RF Kit. -
Página 4: Common Procedures
CM-2300 Firmware The CM-2300 control module is firmware updatable through the internet. In the event Firstech makes any changes or corrections you can update the module using the grey RS232 Data Port on the control module. This requires the USB updater cable. -
Página 5: Cm-2300 Wire Chart
This can also be used to trigger factory rearm. To change dome light output settings, You will need to test the wire for proper polarity and set the jumper on the side of the CM-2300 for review Option 2-04. -
Página 6: Connector 4 (Cn4), 4-Pin (Shock Sensor Port)
Pin 6 Black/White - Auxiliary Input 2 – This wire functions as a negative (-) instant trigger input. It is selectable based on option 2-13. It can be changed to a negative disarm or negative drive lock control. Please refer to the option tables for details. This wire is required for ignition controlled Connector 7 (CN7), 4-Pin (RS232 Data Port) door locks. -
Página 7: Option Menu Descriptions
2 by the remote. Please see page 16 for details. On While 2-07 Secure Aux Output Armed 1-03 Driver’s Priority Unlock – This lets you use the CM-2300 to unlock the driver’s door before the 2-08 Aux 1 Output 0.5 sec Latched 20 Seconds Program rest of the doors as in some factory systems. -
Página 8: Option Programming
CM-2300 locks the doors and when ignition is turned off it will unlocks the doors. This setting and Auxiliary 2 input are required for ignition controlled door locks. Connecting this wire to a (-) output from a relay triggered by the vehicle’s foot brake is recommended for ignition controlled door lock activation. -
Página 9: Option Programming Using The Ft-Op500-Kit
Option 1-13: Siren/Horn Mute Control From Remote Hold Trunk Lock + Key Tap Key Tap Lock Tap Unlock Tap Star Used to enable the remote mute function Option Button for for 3 seconds Button Button Button Button Menu 2 1) Open the Vehicle Door 3 seconds 2) Turn on Ignition ( within 5 seconds ) 3) Press and Release Lock Button... -
Página 10: Frequently Asked Questions
“Success Good.” How do I set the auxiliaries? A: The CM-2300 has programmable auxiliary outputs. You have four preset timed options to program your auxiliaries for. You must have an Option Programmer (OP500) to set a specific time output for the auxiliaries. - Página 11 8101MAUSC001900...