Environmental Protection - Crown CT26011HX Manual Original

The first speed - you can find the values of
the revolutions per minute range in the tech-
nical specifications table.
The second speed - you can find the val-
ues of the revolutions per minute range in
the technical specifications table.
Stepless speed adjustment
Speed is controlled from 0 to maximum by
pressing force of on / off switch 6� Weak
pressing results in low revolutions, which
enable a smooth power tool switch-on�
Recommendations on the power tool
operation
Stirring various substances
Do not process explosive substances
(for example, highly inflammable sol-
vents) and materials with ignition tem-
perature of lower than 21°С. Study the
manufacturer's instructions for such kind of mate-
rials carefully and stick to them.
• The selection of stirring paddle type depends on the
type of substances stirred� Use stirring paddles with
left-hand blade spinning for low-viscosity substances
(dispersed paints, lacquers, sealing compounds, liquid
cement solution)� Use stirring paddles with right-hand
blade spinning for high-viscosity substances (ready-
made plastering solution, concrete, putty, polymeric
resins)�
• During work, you must tightly hold the power tool
and ensure you stand firmly. You should hold the pow-
er tool with both hands it makes the implementation of
works more convenient and increases the degree of
control over the power tool�
• Fix the container with the mixture stirred carefully
during the work�
• Move the power tool upward, downward and in cir-
cular movements to stir the mixture in the best manner
in its whole volume�
• After finishing the works, wash and wipe stirring
paddle�
Power tool maintenance / preventive
measures
Before carrying out any works on the power tool
remove the battery 1.
Battery maintenance instruction
• Charge timely before the battery 1 is completely
exhausted� Stop operation in low power and charge
it immediately�
• Do not overcharge when the battery 1 is full, other-
wise it will shorten the life time�
• Charge battery 1 in the room temperature of 10°C
to 40°C (50°F to 104°F)�
The manufacturer reserves the possibility to introduce changes.
• Charge battery 1 every 6 months without operation
for a long time�
• Replace worn out batteries in time� Decline of pro-
duction or a significantly shorter runtime of the power
tool after charging indicates aging of the battery 1 and
the need for replacement� It should be taken into ac-
count that the battery 1 may discharge faster if the
works take place in the temperature below 0°С.
• In case of long time storage without use, it is recom-
mended to store the battery 1 at room temperature, it
should be charged to 50%�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 7�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.crown-tools.com�
Transportation of the power tools
• Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Li-Ion batteries
The contained Li-Ion batteries are subject to the Dan-
gerous Goods Legislation requirements� The user can
transport the batteries by road without further require-
ments�
When being transported by third parties (e�g�: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed� For prepa-
ration of the item being shipped, consulting an expert
for hazardous material is required�
Dispatch batteries only when the housing is undam-
aged� Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around
in the packaging� Please also observe possibly more
detailed national regulations�

Environmental protection

Recycle raw materials instead of dispos-
ing as waste.
Power tool, accessories and packaging
should be sorted for environment-friendly
recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
English
21