HIKVISION DS-PM-WI1 Manual De Usuario

Wireless Single Input Expander
Product Information
COPYRIGHT ©2019 Hangzhou Hikvision Digital
Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among
others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries
(hereinafter referred to be "Hikvision"). This
user manual (hereinafter referred to be "the
Manual") cannot be reproduced, changed,
translated, or distributed, partially or wholly,
by any means, without the prior written
permission of Hikvision. Unless otherwise
stipulated, Hikvision does not make any
warranties, guarantees or representations,
express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Control Panel
The Manual includes instructions for using and
managing the product. Pictures, charts,
images and all other information hereinafter
are for description and explanation only. The
information contained in the Manual is
subject to change, without notice, due to
firmware updates or other reasons. Please
find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the
guidance of professionals.
Trademarks
Acknowledgement and other Hikvision's
trademarks and logos are the properties of
Hikvision in various jurisdictions. Other
trademarks and logos mentioned below are
the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, THE PRODUCT DESCRIBED,
WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED "AS IS", WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES
NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY,
FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO
EVENT WILL HIKVISION, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE
TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH
INTERNET ACCESS, THE USE OF PRODUCT
SHALL BE WHOLLY AT YOUR OWN RISKS.
HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER
DAMAGES RESULTING FROM CYBER ATTACK,
HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION.
PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT
IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. HIKVISION
SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE
PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN
THIS MANUAL AND THE APPLICABLE LAW,
THE LATER PREVAILS.
English
Diagram Reference
1
Appearance
1 Indicator
Under the signal strength checking mode:
Green- Strong signal Red-Weak signal
Tamper Buttonn
2
- Tampering Alarm: Trigger tampering alarm when
the expander is removed.
- Format: Power the expander off. Hold the tamper
button and power the expander on at the same
time.The indicator flashes three times when the
formatting is completed.
2
DIP Settings
Set the DIP before powering on for the first time
use.
Use a flat-head screwdriver to dig the groove to
1
disassemble the device. Remove the front panel.
Do not disassemble the device with sharps.
Turn the DIP switch to ON to enable the indicator.
2
a
b
Enable the indicator. Disable the indicator.
3
Single Input Expander Wiring
1 Expander 2 Third -party detector
T1 Signal Input T2 GND
COM R Red Wire
T4
The relay output of the third-party detector is the
signal input of the expander.
4
Expander Power-on
Remove the insulating strip to power on the Expander.
5
Register the Expander via APP
1.Log in to the APP Store and input "Hik-Connect" to search
the mobile client. Download and install Hik-Connect to your
phone.
2.After installing, tap to run the client.
3.Power on the security control panel.
4.Log in the Hik-Connect and tap the icon"+" at the
upper-right coner of the Hik-Connect page to add the
security control panel. You can scan the QR code on the
device rear panel or package box, or input the device serial
No. manually to add the device when the device is in the
registration mode.
5.After adding the security control panel, tap the alarming
status icon on the right of the security control panel's name
to enter the Partition page.
6.Tap the"+" icon on the Partition page to add the
peripherals.
6
Expander Installation
1. Check Signal Strength
1) Enter the signal checking mode by operating on the
control panel. Wait for the voice announcement to finish.
2) Hold the TAMPER button for 2 seconds to trigger the
tampering alarm, and then observe the light of signal
strength indicator.
-Expander indicator turns green: Strong Signal.
2. Install the Expander
1mm Sponge Tape
Paste the sponge tape on the rear side of the expander.
Paste the expander on the required place.
When the device is dismantled, the TAMPER will pop up,
trigger the alarm and upload. To make the TAMPER work
properly, the thickness of the sponge tape should be no
more than 1mm.
1
1
2
T3 NC
B Black Wire
6
Specification
3
2
T1
T2
1
1 2
RF Frequency 433MHz
RF Modulation FM
Transmission Rate 10.0kbps
RF Transmission Distance 800m (open area)
Zone Input Type 1 NC Input
CR123A/3V
Battery
Life span: 2 Years
Tamper 1
Indicator 1 (green/red)
Internal Button 1
1 DIP switch
DIP Switch
For turning on/off indicator
Material PC+ABS
Installation Environment Indoor
Temperature –10 ℃ to 55 ℃
Humidity 10% to 90%
Dimention（L*W*H) 84mm*25mm*21mm
Weight 38.5g
Installation Tpye Tape
T3
R
T4
B
2
a b