Technical Specifications; Identification Of The Product; Safety Instructions; Ambient Conditions - PLYMOVENT CB-WCS Instrucciones Pare El Uso

PREFACE
ENGLISH
Using this manual
This manual is intended to be used as a work of
reference for professional, well trained and authorised
users to be able to safely install the product mentioned
on the cover of this document. Take your time to
carefully read and understand the manual before
mounting the CB-WCS. Always keep the manual with
the product.
The figures referred to in the text, can be found in the
back of this manual.
Pictograms and symbols
The following pictograms and symbols are used in this
manual.
Suggestions and recommendations to
simplify carrying out tasks and actions.
CAUTION
Procedures, if not carried out with the
necessary caution, could damage the
product, the workshop or the environment.
1 IDENTIFICATION OF THE
PRODUCT
The identification plate (fig. 1) contains the following
data:
A product name
B serial number
C supply voltage and frequency (50/60Hz)
D power
2

SAFETY INSTRUCTIONS

The manufacturer does not accept any liability for
damage to the product or personal injury caused by
non-observance of the safety instructions in this
manual, or by negligence during installation, use,
maintenance and repair of the product mentioned on
the cover of this document.
The user of the product is always fully
responsible for observing the local safety
instructions and regulations.
• Everyone working on or with the product, must be
familiar with the contents of this manual.
• Never change the order of the steps to perform.
• The product has been designed exclusively for
connecting a stationary welding fume extractor
(SFS) [Statiflex 400-MS], an in the extraction arm
integrated working light (WL) and/or automatic
start/stop device (AST or WCS) and an extraction
fan (FAN 14/28/42) [SF 1400/2400/4200]
mains. Using the product for other purposes is
0507346050/CB-WCS/010111/C
considered contrary to its intended use. The
manufacturer accepts no liability for any damage or
injury resulting from such use. The product has
been built in accordance with state-of-the-art
standards and recognised safety regulations.
• Only use the product in technically perfect
condition.
• Inspect the product and check it for damage.
• Protect the product against water and humidity.
• Never use the product in an explosive environment.
• Make sure that the workshop contains sufficient
approved fire extinguishers.
3

TECHNICAL SPECIFICATIONS

3.1 General
Isolation class
3.2 Dimensions
See fig. 2; dimensions in mm.
3.3 Electric system
See the identification plate and the separately supplied
electric diagram.
3.4

Ambient conditions

Min. operating temperature
Max. operating temperature
Max. relative humidity
4

GENERAL DESCRIPTION

The product has been designed especially for
connecting an automatic start/stop device (WCS) and
an extraction fan (FAN 14/28/42)
4200] to the mains.
The product can also be used for connecting a
stationary welding fume extractor (SFS)
MS], an in the extraction arm integrated working light
(WL) and/or automatic start/stop device (AST) to the
mains.
The control box (CB-WCS) -which is used for a fixed
installation- can be used for various supply voltages
and frequencies. Also the following thermal relays
(NTR) can be built in:
- NTR 1,4 - 2,0 A
- NTR 1,7 - 2,4 A
- NTR 2,2 - 3,2 A
- NTR 3,0 - 4,7 A
- NTR 4,0 - 6,3 A
- NTR 5,5 - 8,0 A
- NTR 7,5 - 10,5 A
to the
- NTR 10,0 - 14,0 A
IP 55
5°C
45°C
80%
[SF 1400/2400/
[Statiflex 400-
EN - 5