RCA CRF935 Guía De Conexiones

Universal DVD Hookup Kit Universal DVD Hookup Kit
HOOKUP
HOOKUP
GUIDE
GUIDE
INCLUDES:
one RF modulator
one A/V cable
one coaxial cable
CRF935
Congratulations on your purchase of the Universal DVD
Hookup Kit.
This unit is one‑of the most sophisticated, yet easy to use, RF modulators
available‑today! This complete kit includes everything you need to add an
additional input source to your TV. Connecting new video sources to your
TV is as easy as 1,2,3!
Your RF modulator was designed to rest
either horizontally or vertically.
1
1. Unplug your current RF feed from the TV—this is the wire coming from
your antenna, cable, or satellite. Plug it into the ANT IN connector on the
RF modulator.
2
2. Connect your video source
Video Source
(DVD, gaming‑console or
camcorder) to the‑modulator
by‑matching the colored
AUDIO
connectors on the back of
the video source marked
VIDEO
VIDEO/AUDIO OUT to‑the
corresponding input jacks on
S-VIDEO
the‑back of the RF modulator.
Use the included A/V cable.
Be sure to match the colors on the ANT IN
connectors to those on the jacks.
If you only have one audio output CHANNEL
4
on‑your video‑source, just use 3
TO TV
either the‑red or white connectors.
Note:
For select models (CRF935, DC 9V
A/V Cable
CRF910) you can use an s‑video
output on your video source. Instead of
RF Modulator
connecting the yellow video cable, use an
optional s‑video cable (sold separately) to
connect the s‑video output on your video source to the s‑video input on the RF
modulator. You will still need to connect the stereo audio cable (red, white connectors)
for audio playback.
3
3. Take the included coaxial cable and connect the TO TV to the ANT IN on your
TV. Plug in the AC adapter. Turn your TV to Channel 3 or 4 (whichever is not
used‑for‑broadcasts in your area). Select the same channel on the switch on the back
of‑your‑modulator.
Note:
Turn off equipment while making connections.
Troubleshooting
If you encounter signal interference when using the RF modulator, try to eliminate
the interference by:
• moving your RF modulator away from the receiver
• connecting your RF modulator to an outlet that is on a different electrical circuit
from the‑receiver
FCC Compliance
This device complies with Part 15 of FCC Rules. Operation is subject
to the following two‑conditions:
(1) This device may not cause harmful interference, and (2) this device
TV must accept any interference received, including interference that may cause
undesired operation.
VHF/UHF
Your modulator might cause TV or radio interference even when it is operating
properly. To‑determine whether your modulator is causing the interference,
turn it off. If the interference‑goes away, your modulator is causing it.
This product meets the applicable Industry Canada technical specifications.
75-Ohm
Coaxial
Try to eliminate the interference by:
Cable
• moving your RF modulator away from the receiver
• connecting your RF modulator to an outlet that is on a different electrical circuit
from the‑receiver
• contacting your local store for help
If you cannot eliminate the interference, the FCC requires that you stop using
AC Adapter
your RF modulator. Changes or modifications not expressly approved by the party
responsible for compliance could void the user's FCC authorization to operate
this equipment.
Note:
With this unit, the audio signal will be modulated to mono.
Note to the CATV System Installer:
This reminder is provided to call the CATV
system installer's attention to article 820‑22 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of‑the building, as close to the point of cable
entry as practical.
Specifications
Video carrier output level ............................................................................ 69dBµV
RF output channels ......................................................................................... 3 or 4
RF output impedance .................................................................................75 Ohms
Audio input impedance ....................................................................... 13±3K Ohms
TV to ANT insertion loss 50‑806 MHz ...........................................................‑2dB
AC adapter .......................................................................................9 VDC/100mA
Dimensions ...........................................5 23 /
32
Weight ............................................................................................. 15 oz (.430 kg)
x 3 x 1 13 / inches (145 x 75 x 30 mm)
64
©2004 THOMSON INC.
10330 North Meridian Street
Indianapolis IN 46290
CRF935 NA IB REVA