Coplax Stylies Aquarius Manual Del Usuario página 13

control (14) on the Control panel (10) , and set it at your desired output level (low, me-
dium, high, or turbo).
6. In "manual" Mode, the desired humidity level can be set (40-75% and continuous opera-
tion 'Co') manually by pressing the Humidity control (16) repeatedly (the Humidity indica-
tor(17) blinks with the desired humidity level selected). A few seconds after this input has
been taken, the indicator (17) stops blinking and switches to show the current room
humidity level again.
7. Information: Once the desired humidity is reached, the device stops and the Humidity
indicator (17) blinks. The device measures the humidity level every 30 minutes (when
the device is measuring the humidity the Fan (9) will be still running for1-2 minutes). If
the measured humidity level falls below the set value, the device starts the humidification
process again, and the Humidity indicator (17) stops blinking.
8. Mode 'M' – the device has 3 different pre-programmed modes: Clean, Auto, and Night.
You can select and change among these modes by pressing the 'Mode' control (18) on
the Control panel (10).
9. Clean mode: This mode is ideal for cleaning and descaling the device. Under this mode,
the Disc assembly (8) is powered but the Fan (9) is not running, therefore, no air is blown
into the room.
10. Auto mode: Under this mode, Aquarius is set automatically to keep the humidity level at
45%. The lower the current room humidity level is, the higher the speed of the Fan and
therefore the higher the humidity output is selected by the program.
11. Sleep mode: this mode is ideal when you want the device run quietly during the night. The
illumination is dimed and the device is set to a humidity level of 45%. The humidification
output (Fan speed) is set at its lowest level.
12. You can also use Aquarius to disperse fragrances in the room air. To add fragrance, you
can draw out the Aroma box (7) from its tray and pour less than 2 drops in the box, and
then put it back into the tray. We ask your kind attention to use as less as possible the
fragrance in the Aroma box, an excessive dosage may result in malfunctions and even
damages to the device.
13. Tip: If you wish to change the fragrance to a different one, draw out the Aroma box (7)
from its tray, clean the plastic cage with soap and replace the cotton inside the box with
a new one. Now Aquarius is ready again to take a new fragrance and to disperse in your
room air.
14. As soon as the 'no water' LED indicator (13) is illuminated in red, the Water tank (3) must
be refilled. Pull out the Water tank and the Water tray (5) until you are able to lift the
tank (3) (approx. 4 cm), take off the Water tank cover (4) from the Water tank and fill the
Tank with clean fresh water (approx. 4.5 liters). Put the Tank cover (4) back onto the Tank
tightly and put the tank into the Tray (5), push the tray gently back to its original position.
After the tank has been placed into the device, the Aquarius will restart automatically in
a few seconds.
CLEANING
After each use and before the maintenance, the device must be switched off and the power cable
must be disconnected the from the power socket. Therefore, before the cleaning of Aquarius, you
must disconnect the power cable(2) first.
Please note: Never immerse the device in water (risk of short circuit).
To clean the surface of the device, wipe off the dusts with a damp cloth and then dry thoroughly.
•
To clean the inside parts of the device, you should pull out the Water tray (5) containing the
•
Disc assembly (8). This Disc assembly (8) and the Water tank (3) need to be cleaned every 2
weeks. Thoroughly clean the container using a brush. If there are lime scales, please soak the
container in a descale-agent and then rinse with clean water thoroughly. In order to clean the
10