Access Options; Setting Access Options; Setting Individual Access Options (2-9 Cats); Setting Timer Control / Lock For All Cats - Petmate CAT MATE Elite Instrucciones De Operación

4. Access Options

The access options available are shown below.
'In & Out' Your cat(s) can come in and out of the flap
'In Only'
Your cat(s) can come in through the flap but cannot leave
through the flap
'Out Only' Cat(s) can go out through the flap but cannot enter through
the flap
'Locked'
Cat(s) cannot use the flap
4.1 Setting Access Options for ALL Cats
If you wish ALL of your cats to have the same access option, e.g. you require ALL
cats to be able to come in and go out of the flap, proceed as follows:
4.1.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.
4.1.2 Repeatedly press the '4 WAY' button to scroll through the available access
options (Fig. 7), until you come to the one you want.
4.1.3 Press the 'SET' button to save the setting.

4.2 Setting INDIVIDUAL Access Options (2-9 Cats)

NOTE: This feature is only available on ID Disc Cat Flap with Timer Control
(Ref. 305).
If you wish to assign an individual access option to each of your cats, e.g. to keep
Cat 1 'LOCKED' in but allow Cat 2 'OUT ONLY', proceed as follows:
NOTE: This setting will not prevent a cat that is not allowed out following 'head to
4.2.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.
tail' another cat that is allowed out.
4.2.2 Repeatedly press the '4 WAY' button until 'IND' appears on the LCD display.
4.2.3 Press the 'SET' button to save the setting.
4.2.4 Repeatedly press the '4 WAY' button until the required access option for Cat
1 is obtained.
4.2.5 Press the 'SET' button to save the setting.
4.2.6 Repeat 4.2.4 and 4.2.5 above for all of your cats with a programmed
I.D. Disc.
NOTE: To see the individual settings you have made for your cat(s) at any time,
press the '4 WAY' button for 1 second and release repeatedly.
4.3 Setting Timer Control/Clock for ALL Cats
If you wish to set your cat flap to ensure that ALL cats have a particular access
option, over a selected timed period, e.g. to keep your cat(s) in at night between
19:00 and 06:00, you will first need to decide:
6
a) Which lock setting should apply DURING the timed period, (in the above
example 'IN ONLY' will apply). Outside the timed period, the lock setting made
in section 4.1 or 4.2 will apply.
b) When the timed period should 'START' (In the above example 19:00hrs).
c) When the timed period should 'FINISH' (in the above example 06:00hrs).
d) You will also need to know the current time.
Proceed as follows:
NOTE: if you do not press a button for more than 60 seconds the display will revert
to normal and you will need to start again.
4.3.1 Press the 'TIMER' button for 5 seconds until the Timer function indicator
flashes.
4.3.2 Repeatedly press the '4 WAY' button to select the required access options
from: 'IN & OUT', 'IN ONLY', 'OUT ONLY', 'LOCKED' or 'OFF'.
4.3.3 Press the 'SET' button to save the setting.
4.3.4 The display will show time with the Minute symbol flashing. Repeatedly
press the '+' button until the current Minutes setting is shown (i.e. 10 if the
current time is 12:10).
4.3.5 Press the 'SET' button to save the setting.
4.3.6 The display will now show the time with the Hour symbol flashing.
If you wish to change between a 24 hour clock and AM/PM setting, press
the 'TIMER' button.
4.3.7. Repeatedly press the '+' until the correct Hour setting is shown (e.g. 12 if
the current time is 12:10).
4.3.8. Press the 'SET' button to save the setting.
4.3.9. The display will show the word 'START' and the minutes will flash. Press the
'+' button until the desired minutes setting is shown, (in the above example
'00'). Press the 'SET' button to save the setting.
4.3.10 Then set the hours in the same way (in the above example 19:00).
4.3.11 The display will show the 'FINISH' time. Set in the same way as the 'START'
time. Remember to press 'SET' to save the setting.
When the Timer is set, the Timer function indicator (Fig. 1) will be shown on the
display.
When the timed lock is active, the access option symbol chosen at 4.3.2 will
flash slowly.
To check the time settings, briefly press the 'TIMER' button and release. The
display will show the timed access option selected and the 'START' time. Press the
'TIMER' button again to show 'FINISH' time. The display will revert to current time
after 5 seconds.
7