Joovy CocoonX2 Manual Del Usario página 3

2 Rear Wheels
• DO NOT unfold the stroller at this time.
• Position the stroller upside down in a clean dry place.
• Press the middle button of the rear wheel hub (See Figure 2.1) and insert the axle into the rear wheel housing. See Figure 2.2. Push
firmly to lock in the wheel. Pull the wheel away from the stroller to ensure it is securely installed. Repeat for the other side.
• To remove the rear wheels, press the middle button of the rear wheel hub (See Figure 2.1) and pull the wheel away from the stroller.
3 Front Wheels
• Press the release button located on the back of the front wheel housing (See Figure 3.1) and insert a front wheel post into the housing.
See Figure 3.2. Pull the wheel away from the stroller to ensure it is securely installed. Repeat for the other side.
• To remove a front wheel, press the release button located on the back of the front wheel housing and pull the wheel away from the stroller.
4 Unfolding the Stroller
• Position the stroller so it is resting on all four wheels.
• Engage the linked rear brake (see Using the Rear Wheel Brakes) and position the stroller with the handlebar closest to you.
• Pull upwards on the handlebar until the stroller is partially unfolded. See Figure 4.1.
• Open the zippers on the access door at the rear of the stroller. See Figure 4.2.
• Locate the locking clamps on EACH side of the frame inside the compartment and rotate them all the way towards the front of the stroller.
See Figure 4.3.
• Pull upwards on the handlebar and firmly pull the rear support tube towards you until an audible click is heard. See Figure 4.4.
NOTE: If the stroller does not open or seems stuck, check to ensure that the clamps are not interfering with the seat back.
• Grasp a locking clamp and rotate the clamp towards you. Secure the clamp onto the tube until it is locked into place. See Figure 4.5.
• Repeat this step on the other side until BOTH clamps are locked securely in place.
5 Using the Rear Wheel Brakes
• To engage the rear wheel brakes, push down on the brake lever. See Figure 5.1. The lever will lock both wheels. Check that the brakes
are properly applied by attempting to push the stroller backwards and forwards.
• To release the brakes, gently lift up on the brake lever. See Figure 5.2.
Always make sure the wheel brakes are engaged when the stroller is not being pushed so that the stroller will not roll
away. Never leave stroller unattended, especially on a hill or incline, as the stroller may tip over or slide.
6 Operating the Hood
• The front of the stroller can be used in three positions: fully opened, closed with mesh window, and closed with mesh window and
weather shield.
• To configure the hood with the mesh window and weather shield closed, zip the mesh window closed around the seating compartment.
See Figure 6.1. Then, pull the weather shield down over the mesh window and attach the Velcro® at the bottom to secure it closed.
See Figure 6.2.
• To configure the hood with only the mesh window closed, detach the Velcro® on the weather shield, neatly roll the weather shield up and
secure it under the elastic loops at the top corners of the hood. See Figure 6.3.
• To configure the hood in the fully opened position, roll the mesh window AND the weather shield up together and secure them under the
elastic loops as shown in Figure 6.4.
NOTE: The top rear portion of the hood has a roll back window. To open, pull the forward edge up, roll the flap back and secure it using
the elastic loop attachment. See Figure 6.5.
7 Securing/Removing a Child
There are three height adjustment positions for the shoulder harness straps. For a younger child, the shoulder straps should be positioned
through the lower sewn-in loops on the seatback. For a young child that is tall, the shoulder straps may be positioned through the upper
sewn-in loops on the seatback. For a taller child, use the shoulder straps WITHOUT positioning them through these sewn-in loops. To
re-position the shoulder straps, unbuckle them from the harness buckle and feed these straps through the sewn-in loops, ensuring that they
are not twisted. Re-buckle the shoulder straps onto the harness buckle to secure them.
• Before loading or unloading, ensure that the wheel brakes are engaged.
• To unlatch the buckle, press the center button and remove the male ends of each buckle. See Figure 7.1.
• Carefully place the child in the seat with the shoulder straps over their shoulders and chest. Then place the crotch strap between the
child's legs.
• If necessary, reattach the shoulder straps with the waist straps. See Figure 7.2.
WARNING
!
ALWAYS keep children away from the stroller when unfolding.
ALWAYS secure the clamps on BOTH sides before use.
WARNING
!
EN FR ES