InSinkErator F-HC3300C Manual De Instalación página 6

CARE AND USE
Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing
unit. Use only a properly earthed (grounded) and polarized electric outlet.
ADJUSTING THE THERMOSTAT
approx. 96°C
Factory temperature pre-set is
96˚C. To reset the thermostat
to 96°C, turn the indicator one
notch to the right of vertical.
After adjusting, depress the tap
handle for 20 seconds for water
to re-heat to the new setting.
I
To adjust water temperature, turn
thermostat dial on the front of the tank
clockwise to increase temperature
or turn anticlockwise to decrease
temperature. Repeat if necessary.
All changes should be minimal.
Scalding Hazard: Do not allow water
to boil. May result in severe burns.
SEASONAL STORAGE/DRAINAGE
Anytime the steaming hot water tap is not used for
extended periods of time, unplug and drain unit. If
it is below freezing you will need to unplug the unit
and drain it.
I
Disconnect power from unit (unplug unit).
I
Push hot water tap lever and allow water
to flow until it is cool.
I Shut the cold water tap off at the valve.
I Disconnect tubes from the tank.
I
Unhook tank from wall.
I
Hold tank upside down and drain the
water into the sink.
I
Towel dry any water drippings from
tank area.
I Reinstall tank to wall and
reconnect tubes.
I
Remove and discard filter cartridge,
if applicable.
I
To put back into working order, install
new filter cartridge (if applicable) and
turn on cold water supply at valve.
Depress the hot water dispenser faucet
lever and hold until water flows from the
spout. Reconnect the electrical cord.
CLEANING THE TAP AND TANK
I Only use mild cleaners to clean the tap
and plastic components.
I
Cleaners with acids, abrasives, alkaline,
and organic solvents will result in
deterioration of the plastic components
and void the warranty.
6
FILTER GUIDE AND REPLACEMENT
Replace filter cartridge when there is an obvious
decrease in water flow to the tap or if there is an
objectionable taste or odour to the water.
When the inlet and outlet ports have been closed
and the filter's internal pressure has been relieved,
water (about 60ml) will discharge from vent line.
If the new filter cartridge cannot be inserted,
insert the old one and turn until it stops, remove it
and then retry the new cartridge.
It is recommended that carbon filters be replaced
every 6 months.
Filter replacement instructions:
I Replace with an InSinkErator filter.
®
I
Place pan or dish towel under the filter to
catch water drainage during change.
I
Slowly turn the cartridge anticlockwise
completely until it stops (1/4 turn).
I
Pull cartridge straight down and discard.
I
Insert new cartridge into filter head.
I
Top surface of cartridge will become
flush with the bottom of the filter head
when fully engaged.
I
Turn the cartridge clockwise until it stops
(1/4 turn).
I
Align the in/out arrow on the head and
bracket assembly to the in/out arrow on
the cartridge.
I Open tap to expel trapped air.
Run water for 3 minutes before usage.
I
PROPERTY DAMAGE
I
Regularly inspect the unit for any signs
of leakage. If there are signs of water
damage, immediately remove the unit
from service.
I
To avoid water damage from leakage,
replace all cut, loose or split tubing.
I
A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector,
should be used in those applications
where any leakage could cause
property damage.
Electric Shock Hazard: Using an ungrounded (no earth ground) or improperly
connected appliance can result in serious injury or death from electrical shock.
This appliance must be earthed (grounded). This steaming hot water tap is equipped with a cord that has a
grounding conductor and earth ground pin. The plug must be connected to an appropriate outlet that is properly
installed and earthed (grounded) in accordance with all local codes and ordinances. Do not modify the plug
provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Check with a qualified electrician or tradesman if you are in doubt as to whether the steaming hot water tap is
properly earthed (grounded).
Personal Injury: This tank is a non-pressurised tank. DO NOT modify this system. DO
NOT close vent tube or connect other types of taps or valves to the tank. Use only the
InSinkErator tap supplied. Use only parts provided. Contact an authorised InSinkErator
Service agent for repairs or replacement components.
Fire Hazard: To minimise possibility of fire, DO NOT store flammable items such as rags,
paper or aerosol cans near the tank. DO NOT store or use petrol or other flammable
vapours and liquids in the vicinity of this or any other appliance.
Property Damage: To avoid water damage, replace any loose or split tubing. Periodically
inspect the unit for any signs of leakage and immediately remove from service any unit
suspected of leaking.
A steaming hot water tap, like any water heater, has a limited life and will eventually fail. To avoid
possible property damage and personal injury, this steaming hot water tap should be regularly
examined for leakage and/or corrosion and replaced when necessary. A drain pan, plumbed to
an appropriate drain or outfitted with a leak detector, should be used in those applications where
any leakage could cause property damage. To check for corrosion, examine the appearance of
the dispensed water in a clear glass once every three (3) months. If there is any discoloration or
rusty appearance, unplug and drain unit as described in the Seasonal Storage/Drainage section
on page 6 of this manual. If the water discoloration remains after draining and refilling unit,
discontinue use and contact an authorized InSinkErator service agent.