Simer 2956 Manual Del Usuario página 2

Bombas sumergibles para sumideros y efluentes
Ocultar thumbs Ver también para 2956:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Specifications and Safety
DESCRIPTION
This Submersible Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-
type power cord. Shaded-pole motor is oil filled and
sealed for cooler running. Sleeve bearings on motor
shaft never need lubrication. Automatic reset thermal
protection.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge:................................................1-1/2" FNPT
NOTICE: This unit is not designed for applications
involving salt water or brine! Use with salt water or
brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed as a swimming pool drainer.
PERFORMANCE
GPH (LPH) AT TOTAL FEET (M)
Motor
Series
HP
(1.5m)
CAPACITY GALLONS(L)/HOUR
2956
1/3
(10 599)
2958
1/2
(12 113) (10 220) (7 570)
ELECTRICAL & SWITCH SPECIFICATIONS
Individual
Branch
Motor
Circuit
Series
HP
Req.(Amps)
2956
1/3
15
2958
1/2
15
For parts or assistance, call Simer Customer Service at
5
10
15
(3m)
(4.6m)
2800
2200
1400
(8328)
(5299)
3200
2700
2000
*Switch Setting
in inches (mm)
On
Off
8"(203)
3"(76)
8"(203)
3"(76)
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from func-
tioning normally. To prevent possible water damage
due to flooding, consult your retailer about a sec-
ondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common
sump pump problems and remedies. For more infor-
mation, see your retailer, call Simer customer
service at 1-800-486-7867 or visit our website at
www.simerpumps.com.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before servic-
ing any component.
5. Drain all water from system before servicing.
No flow
at height
6. Secure discharge line before starting pump. An
shown
unsecured discharge line will whip, possibly
below
causing personal injury and/or property damage.
20 Ft.
(6.1M)
7. Check hoses for weak or worn condition before
each use, making certain that all connections are
24 Ft.
(7.3M)
secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
9. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working
with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
11. When wiring an electrically driven pump, follow
all electrical and safety codes that apply.
12. This equipment is only for use on 115 volt (sin-
gle phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type
plug.
1-800-468-7867
2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2958

Tabla de contenido