en
ENGLISH
The diamond cut-off wheels continue running after
the machine has been switched off.
Always wear protective goggles, dust mask, gloves,
ear protectors and sturdy shoes when working with
this tool.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked side handle must be
replaced. Never operate a machine with a defective
side handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Do not switch on the machine if tool parts or guard
devices are missing or defective.
Reduce dust exposure:
Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of these chemicals are: Lead from lead-
based paints, crystalline silica from bricks and
cement and other masonry products, arsenic and
chromium from chemically-treated lumber, hard
wood like oak or beech, metals, asbestos.
The risk from exposure to such substances will
depend on how long you or bystanders are being
exposed.
Do not let particles enter the body.
To reduce your exposure to these substances: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
14
5. Overview
See page 2.
1 Scale for depth of cut
2 Cross handled screw for setting the cutting
depth
3 Side handle
4 Hex screw (guard)
5 Main handle
6 Aperture for the extraction unit
7 Electronic signal indicator
8 Hex screw (guard)
9 Triangular marking (acts as cut indicator)
10 Safety cover
11 Sheath
12 Guide shoe
13 Locking button
14 Screw (for adjusting the position of the side
handle)
15 Slide switch (for switching on/off)
16
Support flange
17
Spacer rings
6. Commissioning
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Mains connection: The wall chaser has an
electronic initial current limitation. It is sufficient for
the socket to which the machine is connected is
secured with a circuit-breaker of type H or a fast-
acting fuse.
7. Groove width
Switch off the machine. Disconnect the mains
plug!
Caution! Never press the locking button (13)
when the machine is running (nor when it is
slowing down)!
See page 2.
- Undo the hex screw (4).
- Undo the hex screw (8) and set the guard (10) and
guide shoe (12) in such a way – see the second
image on page 2 – that you have free access to the
diamond cut-off wheel.
- Press the locking button (13), (with the other
hand) rotate the front diamond cut-off wheel
slowly until the locking button engages perceptibly
and
- with the locking button (13) pushed undo the
sheath (11) with the supplied two hole wrench.