Dry Vacuuming - CleanFreak AI-1260-P Manual De Operación

WET PICK - UP (Only for wet / dry models)
1. Take the motor head out of the tank. Unlock the three snap clamps.
2. Remove the cloth filter and replace the motor head into place.
3. Connect the line cord into a 120 Volts, 60 Hz outlet.
4. Install the water suction accessory.
5. Turn the vacuum cleaner on, using the on / off switch.
6. When finished, turn the vacuum cleaner off, disconnect it and wind the cord around the handle.
NOTE: When the tank is full, the float valve will close the motor intake, preventing any further suction. Never vacuum water
with the power nozzle, the electric hose or the cloth filter.
MAINTENANCE
1. Check the level of the water or dirt in the tank periodically. If it
is full, take the motor head off and empty the tank (see fig. 1).
2. Shake the cloth filter to remove the dust, never wash it. Place
the bag over cage, making sure the elastic band is over the last
wire ring of the cage, fitting snuggly between the last ring and the
motor base covering the entire cage (see fig. 2).
3. Take off the sponge filter at the bottom of the motor head (see
fig. 3). Hand wash it with cold water. Let it dry completely before
placing it again in the vacuum cleaner. Never use heat sources to
shorten the drying time, this can change its shape.
4. Place the motor head over the tank and lock the three snap
latches.
NOTE:
Models AI-1960-P and AI-1660-P, include a drain hose.
CONNECTING HOSE AND ACCESSORIES
MODELS AI-1260-P, AI-1660-P and AI-1960-P
1. Press the plastic coupling of the hose into the suction inlet tube.
2. Press the other end of the hose into the upper extension wands
(the one without coupling ring).
3. Join the wands aligning the button and the hole.
4. To connect the accessories, loosen the ring (do not take it off)
and insert the accessory of your choice. Tighten up the ring again.
5. The crevice tool, the furniture and upholstery brush, and the dust
brush can be connected directly into the hose.

DRY VACUUMING

1. Make sure that the cloth filter and the sponge filter are on their
correct position (see maintenance section).
Make sure both filters are completely dry.
2. Make sure that the head snap clamps are in the closed position.
3. Connect the line cord to a 120 Volts, 60 Hz outlet.
4. Connect the accessory of your choice
(except the water suction accessory).
5. Turn the vacuum on using the on / off switch.
6. When finished, turn the vacuum off, disconnect it and wind the
cord around the handle.
HOW TO INSTALL THE 28.5" SQUEEGEE
Only for Wet / Dry models
1. Remove the 2 screws (1), the spacers (12) and nuts (11) that
are on the squeegee chassis supports
2. Place the flat washers (10), the spacers (2) and the spring loops
(3) in the screw (4).
3. Place the squeegee under the chassis and fix it with the flat
washer (7) and the nut (8).
4. Align the squeegee chassis supports with the supports on the
vacuum cleaner base and place the screws (1) that were removed
on step 1. Place the spacers and nuts in place.
5. Remove the lower handle screw on the right side. And replace
using the spacer (5) and the long screw (6) included.
6. Place the spring loop (9) on the spacer.
FIG. 1
AI-1260-P
AI-1660-P
AI-1960-P
-4-
FIG. 2
FIG. 3
COUPING
HOSE
COUPING
TOP WAND
SECURITY BUTTON
BOTTOM WAND
RING
ACCESSORY