Installation Instructions - Garmin BC 30 Instrucciones De Instalación

BC ™ 30 Wireless Backup Camera

Installation Instructions

Introduction
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Garmin strongly recommends having an experienced installer
®
with the proper knowledge of electrical systems install the
device. Incorrectly wiring the power cable can result in damage
to the vehicle or the battery and can cause bodily injury.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place will void the product warranty.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
These installation instructions do not apply to a specific vehicle
type, and are meant as a guide when installing this product on
your vehicle. For questions specific to your vehicle, you should
contact the vehicle manufacturer.
Device Overview
Item Description
BC 30 receiver cable
™
The GPS device must be powered through this cable to
communicate with the camera.
Transmitter
Camera
Camera mounting bracket
Tools Needed
• Drill and 9.09 mm, or size T (0.36 in.) drill bit
• #2 Phillips screwdriver
• Screws, bolts, or cable ties (to secure the transmitter)
• Solderless wire-splice connector or solder and heat-shrink
tubing
• RV sealant (optional)
Installation
Installing the Receiver
Before you can install the BC 30 receiver cable, you must
update your GPS device to the most recent software version.
Your GPS device may not be compatible with the BC 30 camera
2
WARNING
CAUTION
NOTICE
without the most recent software. See your GPS device owner's
manual or go to garmin.com/express
updating your GPS device.
The wireless camera receiver is built into BC 30 receiver cable
included with your wireless backup camera.
Use the BC 30 receiver cable included with your BC 30
camera to connect your GPS device to vehicle power.
See the owner's manual for your GPS device for more
information about connecting the device to vehicle power.
NOTE: The BC 30 receiver cable includes a traffic receiver. If
your GPS device includes lifetime traffic, the traffic features
continue to function while using the BC 30 receiver cable.
Camera Mounting Considerations
When selecting a location to mount the camera, observe these
considerations.
• You should test a mounting location before you permanently
mount the camera.
• Installing the camera higher on the back of the vehicle
provides a better viewing angle.
• The included bracket can be clipped onto a license plate or
other similar surface, or it can be fastened to the back of the
vehicle using the included self-tapping, panhead screws.
Transmitter Location and Wiring Considerations
The transmitter is not intended to be held or worn on your body
while it is in use.
When selecting a location to install the wireless transmitter,
observe these considerations.
• You should test a proposed installation location before you
permanently install the transmitter.
• Some vehicles do not provide constant minimum voltage to
the reverse lamps. You should use an automotive relay when
connecting the transmitter and camera to a power source that
does not provide constant voltage.
• Although the transmitter can reliably transmit the video signal
over approximately 13.5 m (45 ft.), the location of the
transmitter can affect this range.
◦ The closer you install the transmitter to the receiver, the
more reliable the signal.
◦ The transmitter provides the best signal when either flat
surface is pointing toward the receiver.
◦ Dense metal or appliances
greatly reduce the transmission distance.
◦ The fewer solid objects that exist between the path of the
transmitter and the device, the more reliable the signal.
• If the distance between the camera and the transmitter
exceeds the length of the included cable, additional extension
cables can be used. A 15 m (50 ft.) extension cable can be
purchased, and more than one extension cable can be
installed. See your Garmin dealer or go to
for more information.
for more information about
NOTICE
in the path of the transmitter
www.garmin.com