GRE LLEDP56W Manual De Instalación Y Mantenimiento página 2

Lampara subacuatica
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 4
ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions
before beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Underwater LED PAR56 Lamp, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
• PAR56 LED lamp
• Installation and maintenance manual
2. GENERAL CHARACTERISTICS:
This lamp has been designed to be used fully submerged in fresh water. It is a Class III electric apparatus with very
low safety voltage (12 V with alternating current). The lamp is class 116, in accordance with standard EN 50065.
The floodlamp complies with IPX8 degree of protection at a nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric compo-
nents which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• To correctly light a swimming pool we recommend you:
Install a lamp in the range LED every 20 m² of water surface.
Note: Recommendation valid for light coloured pools. In darker coloured pools or stainless steel pools we recommend
oversizing the proportion of lamps per m².
• It is the responsibility of the fitter to ensure that the area around the connectors is properly insulated.
• The connection boxes should be at least 2 m. from the edge of the swimming pool or water installation.
• The 230/12V transformer supplying the lamp, should be installed 3.5 m. from the edge of the swimming pool or
water installation.
• Conduits installed less than 3.5 m. from the swimming pool edge, should not be lined or covered in metal.
4. ASSEMBLY:
After installation of the housing and the clamp, assemble the projector.
Follow these steps to assemble the PAR56 LED lamp in an underwater projector with an incandescent lamp:
1. Ensure that the lamp is NOT receiving voltage.
2. Remove the lamp unit and the part of the projector and place it on the edge of the swimming pool (this operation is
fully described in the projector manual) (Fig. 1).
3. Dismantle the parts of the projector required to remove the incandescent lamp (this operation is fully described in
the projector manual)(Fig. 2).
4. Loosen the two screws which electrically connect the PAR56 incandescent lamp (Fig. 3).
5. Place the PAR56 LED lamp electrically connecting it with the two connection screws (Fig. 4).
6. Assemble the projector in its initial position (this operation is fully described in the projector manual).
7. Connect the projector to the mains.
5. MAINTENANCE:
This lamp does not require any type of maintenance work. If you notice that the lamp is not working properly, please
contact our customer attention service.
THIS PRODUCT DOES NOT CONTAIN ANY ELEMENTS THAT CAN BE HANDLED, DISMANTLED OR REPLACED
BY THE USER. IT IS FORBIDDEN TO ACCESS INSIDE THE PRODUCT, OTHERWISE THE GUARANTEE OF THE
6. ELECTRICAL CONNEXION (see diagram p.14)
The electrical connection of the monocolour lamps consists solely in turning the system on and off.
7. SAFETY WARNINGS:
• Avoid making contact with the electric voltage.
• Comply with the current standards regarding accident prevention.
• In this regard, the IEC 364-7-702 standards must be observed: WIRING IN BUILDINGS SPECIAL WIRING SWIM-
MING POOLS.
• This lamp is suitable for use in seawater unless projector specifications state otherwise.
• Bag of fastenings
• Warranty booklet
PRODUCT WILL BECOME INVALID.
2

Publicidad

Tabla de contenido
loading

Tabla de contenido