Troubleshooting; Faq - Wabi Baby ALL WA-881XN Serie Manual De Instrucciones

FRESH WATER RINSE
To avoid burns, please be sure that the water has cooled down.
EN
Use a clean towel to absorb all cleaning solution until dry. A dedicated soft
1.
toothbrush may be used to clean stubborn buildup on the Heating Plate.
Fill the Measuring Cup with 100 ml water.
2.
Use a clean towel to absorb all water until dry.
3.
Wipe the Heating Plate with a clean damp towel until no cleaning solution
4.
remains.
Dry the Heating Plate completely with a clean towel.
5.
The sterilizer is now ready for regular use.
6.
IMPORTANT: Never pour the liquid out. WIPE DRY ONLY. There are many air vent openings on
the Electric Base Unit. Attempting to pour the liquid out directly may cause it to flow into the vents.
This will cause permanent damage to the circuit board inside the Electric Base Unit and is not covered
by the warranty.
METHOD 2 -
UNPLUGGED DESCALING WITH VINEGAR OR CITRIC ACID
This descaling method does not use descaling mode.
Unplug the unit.
1.
Dry any remaining water from the Heating Plate with a clean towel.
2.
Choose one of the following, make sure the chosen solution covers the
3.
entire rim; do not exceed the maximum level.
a. Pour 100 ml distilled white vinegar onto the Heating Plate.
b. Pour about 100ml of distilled water onto heating plate. Add 1 teaspoon of food grad citric
acid.
Leave the solution in the Heating Plate for a minimum of one hour or until
4.
the scale has dissolved.
Use a clean towel to absorb the white vinegar until dry. A dedicated soft
5.
toothbrush may be used to clean stubborn buildup on the Heating Plate.
NOTE: Do not use harsh abrasives or cleaning agents (such as bleach) or a scouring pad to
clean the Heating Plate or allow them to come into contact with the unit. They can cause serious
damage.
Repeat steps 2-5 if necessary.
6.
FRESH WATER RINSE
Dry any remaining solution from the heating plate with a clean towel.
1.
Fill the Measuring Cup with 100 ml water.
2.
Use a clean towel to absorb all water until dry.
3.
Wipe the Heating Plate with a clean damp towel until no solution remains.
4.
Dry the Heating Plate completely with a clean towel.
5.
The sterilizer is now ready for regular use.
6.
10
TR OUBLE SHOOTI NG
Indicator Light not a. No power; check circuit breaker or GFCI breaker.
lighting b. Incorrect plug voltage.
Solution: Please make sure the power cord is plugged in. This unit is certified
to be used within 120V 60Hz in North America; if you are in a country using
a different voltage, please be sure to use the proper transformer. Due to the
varying quality of transformers available on the market, please understand
that we do not warranty our product for use with a transformer.
Beeping sound a. Bottle Chamber placed incorrectly.
b. No water was added to the Heating Plate. Please make sure to add 80 ml
of distilled water before selecting your desired mode.
c. Not enough water was added—sterilization may not complete. Please
make sure to add 80 ml of distilled water and start the cycle again.
Indicator Light a. Bottle Chamber placed incorrectly.
flashing
LED flashing "Lo" a. No water was added to the Heating Plate. Please make sure to add 80 ml
of distilled water before selecting your desired mode.
b. Not enough water was added—sterilization may not complete. Please
make sure to add 80 ml of distilled water and start the cycle again.

FAQ

Why are the contents a. When a large number of items are being sterilized, enough time may not
still wet after drying? have been selected to dry them completely.
b. Improper placement of the contents may prevent the hot air from
circulating evenly.
c. Water may be accumulating in the concave bottoms of bottles; shake the
water off before placing them in the Chamber.
Press the DRY mode button to select the desired time setting to dry again,
or see page 7 for adjusting the drying time.
Why is there an odor This may be an indication that the Heating Plate needs descaling. Scale
while sterilizing or buildup is normal and occurs more quickly in hard water areas. See page 9
drying? for descaling your WABI BABY
Why do I detect an Possible water damage to the Electric Base Unit from water flowing into
electrical burning the circuit board through the air vents. Stop using the unit immediately and
smell? contact our Customer Service.
Why are there white This may be an indication that the Heating Plate needs descaling. Scale
spots on the Heating buildup is normal and occurs more quickly in hard water areas. See page 9
Plate, Lid, Chamber, for descaling your WABI BABY
Racks, or Accessory
Tray?
Why does sterilization You may have poured too much water onto the Heating Plate or left too
sometimes take so much water on the contents after rinsing. Try shaking off as much residual
long or so short? water as possible. For shorter cycle, you may not have poured enough
water onto the Heating Plate. Be sure to use 80ml.
Why does water leak a. You may have poured too much water onto the Heating Plate. Any excess
out of the sterilizer? water may flow into the air vents and cause damage to the Electric Base
Unit. Please contact Customer Service for support.
b. make sure the air rotor is locked in the right place where it does not direct
water into the air vent.
Why does the This is an indication of an overloaded circuit. Unplug all other appliances on
unit trip the circuit the same circuit or try the unit on a separate electrical circuit without other
breaker? appliances.
Sterilizer & Dryer.
TM
TM Sterilizer & Dryer.
11
EN