Troubleshooting Guide - Guardian Technologies AC5000 Serie Instruciones De Uso Y Cuidado

Ocultar thumbs Ver también para AC5000 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLING & REMOVING UV-C BULB
CHANGE BULB INDICATOR
The blue light on the front of air cleaner will begin to flash continuously when it is time to replace
the UV-C bulb. Replace the bulb according to the directions then press the UV control button and
hold for 5 seconds to restart the system. The light should remain a constant blue.
REPLACE BULB
AC4825 SERIES
4. The UV-C Bulb is removed by
3. After removing the Combination
carefully grasping the bulb with a
Filter, use a Philips head screw-
clean cloth or tissue and pulling
driver to remove two (2) screws
the bulb straight out of the unit.
and detach the UV-C Metal Shield.
AC5000 SERIES
3.After removing the Combination
4. The UV-C Bulb is removed by
Filter, use a Philips head screw-
carefully grasping the bulb with a
driver to remove four (4) screws
clean cloth or tissue and twisting
and detach the UV-C Metal Shield.
the bulb 1/4 turn. Remove from unit.
IMPORTANT
: The UV-C Bulb should be replaced every 10 - 12 months depending on use.
E-8
Continue reading below for remaining
instructions on how to Install & Remove
the UV-C Bulb for the AC4825 Series and
the AC5000 Series.
1. Remove the Rear Cover of the unit by pushing
Lock & Release Button.
2. After removing the Rear Cover from the unit,
remove the Combination Filter.
Bulb is NOT visible until
the UV-C METAL SHIELD
PULL UV-C BULB
has been removed.
STRAIGHT OUT
OF UNIT
5. The UV-C Bulb is reinstalled by sliding it,
horizontally, back into the slots at the top of the unit.
6. Push and hold UV Control Button for 5 seconds to
reset UV Bulb Change Indicator.
TWIST BULB 1/4 TURN
TO REMOVE BULB
Bulb is NOT visible until the
UV-C METAL SHIELD has
been removed.
5. The UV-C Bulb is reinstalled by reversing the
process in Step 4.
6. Push and hold UV Control Button for 5 seconds to
reset UV Bulb Change Indicator.

TROUBLESHOOTING GUIDE

PROBLEM
SOLUTION
Unit does not operate.
Check that the unit is plugged in.
Check that filter is in place.
Confirm that filter is Genuine Replacement Filter
Call Customer Service.
Unit shuts off unexpectedly.
Check that unit is plugged into a working electrical outlet.
Check that filter is firmly in place.
Check that the Rear Cover is latched firmly in place.
Call Customer Service.
No air circulating from unit.
Unplug unit. Check Pre-/Carbon and Hepa
filters. Clean Pre-/Carbon Filter if
necessary. Replace filter if necessary.
Increase in noise level.
Make sure the filters are clean. Replace if necessary.
Power light is red and flashing.
Replace filter and reset system.
Blue UV-C light is flashing.
Replace Bulb and reset.
What is CADR?
CADR stands for "Clean Air Delivery Rate," which indicates the volume of filtered air delivered by
an air purifier. CADR ratings show the effectiveness of how efficient the air purifier is at capturing
fine particles from things like tobacco smoke and plant pollens from the room.
Clean Air Delivery Rate
From air cleaner to air cleaner, compare the CADR numbers. First look at suggested room size. Then refer
to the Clean Air Delivery Rate (CADR) numbers. The higher the number, the faster the unit filters the air.
Refer to website for individual model CADR numbers.
E-9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ac4825

Tabla de contenido