Dip Switch - CDVI CAA470A Manual De Instalación

INSTALLATIoN MANUAL
CAA470A
2-Door expansion module
should have the same setting as the Lock
Control for the corresponding doors in
Centaur.
Lock #1 = DIP switch 3 (L1 Energize)
Lock #2 = DIP switch 4 (L2 Energize)
oFF =
De-energized:
During a communication failure, the
normal state of the lock output is
De-energized. When Lock #1 or Lock
#2 is activated, power is applied
to the corresponding lock output to
unlock the door. Activation depends
on the setting of the DIP switches 5
& 6 (Access during Communication
Failure).
oN =
Energized:
During a communication failure, the
normal state of the lock output is
Energized. When Lock #1 or Lock
#2 is activated, power is removed
from the corresponding lock output to
unlock the door. Activation depends
on the setting of the DIP switches 5
& 6 (Access during Communication
Failure).
De-energized: no power in normal
state; requires power to activate.
Energized: power in normal state;
remove power to activate.
Access during Communication
Failure (5 and 6)
DIP switches BACKUP1 (5) and
BACKUP2 (6) determine the access
to the protected doors during a
communication failure.
Switch Setting
"No Card"
5 = OFF (0) Access is denied to all cards
6 = OFF (0) and doors are locked until
communication is restored.
8
cdvigroup.com
During a Communication
Failure:
"2 Cards"
5 = ON (1) Access is granted only when
6 = OFF (0) 2 cards of a valid format are
presented to the reader.
"All Cards"
5 = OFF (0) Access is granted when any card
6 = ON (1) with a valid format is presented
to the reader.
"Unlock Door"
5 = ON (1)
Doors are unlocked until
6 = ON (1)
communication is restored.
Activate output on Communication
Failure (7)
DIP switch PULSE 5&6 (7)
determines if OUT5 and OUT6 will
activate during a communication
failure. When DIP switch 7 placed in
the "ON" position, the OUT5 and
OUT6 outputs will activate. For example, the
buzzer on the readers can activate to advise
users that a communication failure has
occurred.

DIP Switch (8)

For future use.
EoL Jumper
Place the EOL jumper ON if the 2-Door
Expansion Module is at the beginning (Start
Point) or at the end (End Point) of the E-bus
Network (see Figure 2). Otherwise, place the
EOL jumper OFF.
Figure 2: Setting the EOL/BIAS Jumpers
EOL Jumper
CTV900A
EOL = ON
GND
+24V 12V
LOCK #1 MICRO CHECK OUT6
LK1+
LK1- 24V AC PRESENT R1/5V
READER +5V
LK2+ 12V +12V SUPPLY R1/0V
EXPANSION PORT
LK2- LOCK #2 LOGIC +5V R1/D0
+24V SUPPLY
COM1 LOW BATT R1/D1
24V
NO1 OUT1 High/Low BIAS Jumpers
NC1 OUT2
RELAY RELAY #1
COM2 1 R1/KA
NO2
RELAY RELAY #2 #3 READER #1 R1/KB
2 DATA
NC2 R1/KC
R1/KD
+12V A+ = Low
+12V
+24V
GND
Z1-2
COM
R2/5V
Z3-4
R2/0V
Z5-6
R2/D0
B- = Low
COM DEF/RUN R2/D1
9.6K/19.2K
Z7-8 ADD 32 OUT3
ADD 16
ADD 8 OUT4
+12V ADD 4
ADD 2 R2/KA
GND ADD 1
READER #2 R2/KB
Z9-10 ON OFF
DATA
COM R2/KC
Z11-12 R2/KD
Z13-14 +12V
COM +24V
Z15-16
HIGH LOW A2+
A+ ON OFF E-BUS B2-
A1+ RING
TX RX GND
B1- BATT
3V A+ TMP
GND LOW HIGH
TMP
NETWORK EOL
HIGH LOW TX RX +
SERIAL
B- PORT 1 2 3 4 B-
DB-9 LOW HIGH S/N
RESET SWITCH E-BUS
CAA470A CAA470A
CA - A470 - A
AC
AC
D1NC LOCK#1 BAT+ D1NC
COM BAT- COM
D1NO STATUS AC OK V+ D1NO
D2NC AUX OK V+ D2NC
LOCK#2 COMM
COM JP120 CHECK BATT V- COM
D2NO 350mA/700mA BATT TRBL V- D2NO
OUT5
SWITCH BACKUP OUT6
SW1 ADD 1 2 1
SW2 ADD 2 0 0 NO CARD
SW3 ADD 4 0 1 2 CARDS
Z1 SW4 ADD 8 1 0 ALL CARDS A+ B- Z1
COM SW5 BACKUP1 1 1 UNLOCK DOOR EOL LOW COM
SW6 BACKUP2
Z2 HIGH A+ Z2
SW7 PULSE 5&6 B-
Z3 SW8 N/D Z3
COM GND COM
Z4 READER#2 READER#1 TAMPER Z4
DATA DATA
TAMPER
TX RX
E-BUS
EOL Jumper EOL Jumper
EOL = OFF EOL = OFF
High/Low BIAS High/Low BIAS
Jumpers Jumpers
A+ = High A+ = High
B- = High B- = High
High/Low BIAS Jumpers
Place the A+ and B- BIAS jumpers on LOW
only if the 2-Door Expansion Module is at
START POINT
END POINT
CAA470A
CA - A470 - A CA - A470 - A
AC
AC
LOCK#1 BAT+ D1NC LOCK#1 BAT+
BAT- COM BAT-
STATUS AC OK V+ D1NO STATUS AC OK
AUX OK V+ D2NC AUX OK
LOCK#2 COMM LOCK#2 COMM
JP120 CHECK BATT V- COM JP120 CHECK BATT
350mA/700mA BATT TRBL V- D2NO 350mA/700mA BATT TRBL
OUT5 OUT5
SWITCH BACKUP OUT6 SWITCH BACKUP OUT6
SW1 ADD 1 2 1 SW1 ADD 1 2 1
SW2 ADD 2 0 0 NO CARD SW2 ADD 2 0 0 NO CARD
SW3 ADD 4 0 1 2 CARDS SW3 ADD 4 0 1 2 CARDS
SW4 ADD 8 1 0 ALL CARDS A+ B- Z1 SW4 ADD 8 1 0 ALL CARDS A+ B-
SW5 BACKUP1 1 1 UNLOCK DOOR EOL LOW COM SW5 BACKUP1 1 1 UNLOCK DOOR EOL LOW
SW6 BACKUP2 SW6 BACKUP2
HIGH A+ Z2 HIGH
SW7 PULSE 5&6 B- SW7 PULSE 5&6
SW8 N/D Z3 SW8 N/D
GND COM GND
READER#2 READER#1 TAMPER Z4 READER#2 READER#1 TAMPER
DATA DATA DATA DATA
TAMPER TAMPER
TX RX TX RX
E-BUS E-BUS
EOL Jumper
EOL = ON
High/Low BIAS
Jumpers
A+ = High
B- = High
EN
AC
AC
V+
V+
V-
V-
A+
B-