BLACK&DECKER ASI500 Manual De Instrucciones página 3

90564808 AS1500.qxd:??????-00 BDL500 laser
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DONʼT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. Itʼs safer than using your hand and it
frees both hands to operate tool.
• DONʼT OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Donʼt carry tool with finger on switch. Be sure
switch is off when plugging in.
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
Volts
120V
240V
Ampere Rating
More
Than
0
6
10
12
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when
you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Do not use tool if switch
does not turn it on and off.
• DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or
explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite
fumes.
ADDITIONAL SAFETY WARNINGS FOR YOUR INFLATOR
WARNING! FOR HOME AND CAR USE ONLY:
• Inflate car and bike tires, balls, rafts, swimming pool floats, air mattresses, and more
in and around the home.
Minimum Gauge for Cord Sets
Total Length of Cord in Feet
0-25 26-50
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
0-50 51-100
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Not more American Wire Gauge
Than
- 6 18 16
- 10 18 16
- 12 16 16
- 16 14 12
3
5/18/10 9:56 AM Page 3
51-100 101-150
101-200 201-300
16 14
14 12
14 12
Not Recommended