Technical Specifications - aerauliqa QB Serie Manual De Instrucciones

• Assicurare un adeguato rientro dell'aria nel locale, nel rispetto del regolamento vigente, al fine di garantire il corretto funzionamento
dell'apparecchio.
• Qualora nell'ambiente in cui è installato il prodotto sia presente un apparecchio funzionante a combustibile (scaldacqua, stufa a metano etc.,
di tipo non a "camera stagna"), è indispensabilie assicurare un adeguato ingresso d'aria, per garantire una buona combustione e il corretto
funzionamento di tali apparecchi.
• Effettuare l'installazione in modo che la girante sia inaccessibile al lato della mandata, al contatto del Dito di Prova (sonde di prova "B" della norma
EN61032), secondo le vigenti norme antinfortunistiche.
VERSIONI
BASE
L'aspiratore si aziona tramite interruttore separato ON/OFF oppure tramite l'interruttore luce (fig. 11A).
CON TIMER (con ritardo di spegnimento)
L'aspiratore è provvisto di circuito timer, regolabile da circa 1 minuto a circa 25 minuti agendo sul trimmer (fig. 12B).
Funzionamento: collegato secondo lo schema di figura 12A, dopo l'accensione luce, l'aspiratore si attiva con un ritardo di 1,5 secondi max. Dopo
lo spegnimento luce, l'aspiratore continua a funzionare per il periodo di tempo pre-impostato.
CONFORMITA' NORMATIVA
2014/35/UE Direttiva Bassa Tensione
2014/30/UE Direttiva di Compatibilità Elettromagnetica
secondo lo stato dell'arte delle seguenti norme:
Sicurezza elettrica
EN60335-1(2008); EN 60335-2-80(2005); EN 60335-2-80/A2(2009)
Compatibilità Eletromagnetica
EN 55014-1(2006)+A1+A2; EN 55014-2(1997)+A1(2001)+A2(2008)+IS1(2007)
EN 61000-3-2(2006)+A1(2009)+A2(2009); EN 61000-3-3(2008).
2
G
Installation manual
QB - Axial fan
Introduction
QB (fig. 1) is an axial fan designed to ensure air extraction in small rooms
such as bathrooms e toilets.
Suitable for air discharge directly to the outside or in the presence of short
linear duct (less than 1.5 m).
Wall or ceiling installation.
Read this manual carefully before using the product and keep it in a safe place for reference.
This product was constructed up to standard and in compliance with regulations relating to electrical equipment and must be installed by technically
qualified personnel.
The manufacturer assumes no responsibility for damage to persons or property resulting from failure to observe the regulations contained in this
booklet.

TECHNICAL SPECIFICATIONS

• High efficiency aerodynamic fan with "winglet" blades to optimise quietness and efficiency.
• Single phase induction motor with integral thermal protection.
• The fan is double insulated: no earth connection is required.
• Power supply 220V to 240V~ 50/60Hz.
• IPX4 wall installation / IPX2 ceiling installation.
Model Airflow Static pressure Power
Sound pressure
dB(A) @3m
m /h max Pa max W max
3
QB100 72 26 8 26
QB150 250 53 22 42
PRECAUTIONS FOR INSTALLATION, USE AND MAINTENANCE
• The device should not be used for applications other than those specified in this manual.
• After removing the product from its packaging, verify its condition. In case of doubt, contact a qualified technician. Do not leave packaging within
the reach of small children or people with disabilities.
• Do not touch the appliance with wet or damp hands/feet.
• The device is not intended for use by persons (including children) with reduced physical, sensory or mental capacities or those with a lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the device from a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the device.
• Do not use the product in the presence of flammable vapours, such as alcohol, insecticides, gasoline, etc.
• If any abnormalities in operation are detected, disconnect the device from the mains supply and contact a qualified technician immediately. Use
original spare parts only for repairs.
• The electrical system to which the device is connected must comply with regulations.
• Before connecting the product to the power supply or the power outlet, ensure that:
- the data plate (voltage and frequency) correspond to those of the electrical mains
- the electrical power supply/socket is adequate for maximum device power. If not, contact a qualified technician.
• The device should not be used as an activator for water heaters, stoves, etc., nor should it discharge into hot air/fume vent ducts deriving from
any type of combustion unit. It must expel air outside via its own special duct.
• Operating temperature: 0°C up to +50°C.
• The device is designed to extract clean air only, i.e. without grease, soot, chemical or corrosive agents, or flammable or explosive mixtures.
• Do not leave the device exposed to atmospheric agents (rain, sun, snow, etc.).
• Do not immerse the device or its parts in water or other liquids.
• Turn off the main switch whenever a malfunction is detected or when cleaning.
• For installation an omnipolar switch should be incorporated in the fixed wiring, in accordance with the wiring regulations, to provide a full discon-
nection under overvoltage category III conditions (contact opening distance equal to or greater than 3mm).
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Do not obstruct the fan or exhaust grille to ensure optimum air passage.
• Ensure adequate air return into the room in compliance with existing regulations in order to ensure proper device operation.
• If the environment in which the product is installed also houses a fuel-operating device (water heater, methane stove etc., that is not a "sealed
chamber" type), it is essential to ensure adequate air intake, to ensure good combustion and proper equipment operation.
• Install the product so that the impeller is not accessible from the air outlet side as verified by contact with the Test Finger (test probe "B" of the
norm EN61032) in compliance with the current safety regulations.
Fig. 1
3