Important Safety Instructions - Wagan Tech Brite-Nite 2358 Manual De Usuario

2 Million Brite-Nite Spotlight Lantern by Wagan Tech
™
Using the Brite-Nite Spotlight Lantern
• Spotlight: Simply locate toggle switch on the handle of the Brite-Nite Spotlight
Lantern and toggle from "O" to "|" position.
• Lantern: Simply locate the switch at the base of the lamp next to DC input. Slide
switch to turn on.

IMPORTANT SAFETY INSTRUCTIONS

Be sure to charge the unit completely before its first use. This will prolong the life of the
Brite-Nite Spotlight Lantern.
IMPORTANT
Do not turn on lamp in any way while charging. Doing so may damage the unit and is
not covered under warranty. As with all lead-acid cell batteries, when storing, be sure to
recharge the battery fully every 3-6 months to prolong the life of the battery.
AC Charging
Insert the AC charging plug into the charging jack on the base of the lamp, and the
transformer end of the AC adapter into an 110V AC outlet. Make sure the unit is in the
off (O) position before charging. The LED indicator light will go on, indicating that the
spotlight is charging (approximately 15 hours).
DC Charging
Insert the DC charging plug into the charging jack and the cigarette plug end into the
car cigarette socket. Make sure the unit is in the off (O) position before charging. The LED
indicator light will go on indicating that the spotlight is charging (approximately 12 hours).
Replacing the Spotlight Bulb
Halogen Bulb
The 2 million Power Rated Brite-Nite Spotlight Lantern uses a 6V 8W/30W double
filaments halogen bulb. Please go to your local automotive/hardware store for
replacement when bulb has burned out.
NOTE: DO NOT touch the glass of the halogen bulb, as doing so may cause the bulb to
shatter. Please refer to the instructions found on the new bulb for other safety precautions.
Always wear safety glasses when working with hardware.
3
www.wagan.com
User's Manual—Read before using this equipment
Simply unscrew the lamp face and carefully change the bulb. The WHITE wire of the
replacement bulb connects to the Brite-Nite's RED wire; the BLACK wire of the replacement
bulb connects to the Brite-Nite's BLACK wire. After replacing the halogen bulb, screw on
the lamp face, making sure a tight fit to ensure no water will enter the housing.
Fluorescent Bulb
The 2 Million Brite-Nite™ Spotlight Lantern Lantern uses a 7W fluorescent bulb. Please go
to your local hardware store for the replacement bulb when bulb has burned out.
Simply unscrew the main lamp face of the halogen bulb. Using a Phillips screwdriver,
unscrew the panel inside to take out the fluorescent bulb. Gently pull out the old bulb and
replace with the new fluorescent bulb. After replacing the fluorescent bulb, replace the
screws and screw on the lamp face, making sure a tight fit to ensure no water will enter
the housing.
General Safety Precautions
• Do not turn on light while charging the unit. Doing so will damage the unit and
will void your warranty.
• As with all lead-acid cell batteries, when storing, be sure to recharge the battery
fully every 3-6 months to prolong the life of the battery.
• Though durable and built to last, do not drop the unit excessively as this will
greatly reduce the life of the unit.
• Though weather resistant, do not submerge the unit.
• Lens becomes very hot during operation.
• Do not cover lens or reflector during operation.
• Do not shine directly into eyes.
• Switch off and allow it to cool before storage or maintenance.
• When servicing always wear safety glasses when working with hardware.
• Use only supplied chargers.
Disposal/Recycling
All electronic equipment contains materials that can damage the environment if not
properly disposed of. Contact your local authority for disposal or recycling instructions.
© 2010 Wagan Corporation
All Rights Reserved
Wagan and wagan.com are trademarks used by Wagan Corporation
4