Philips AVENT 1.800.54 Manual De Instrucciones página 3

EN Philips AVENT Electric Bottle and Baby Food Warmer
11. Do not place on or near a hot gas or
electric burner, or in a heated oven.
12. Extreme caution must be used
when moving an appliance containing
hot oil or other hot liquids.
13. Do not use appliance for other than
intended use.
14. When in use the warmer contains
hot water.
15. Before plugging in the warmer for
the first time, ensure the voltage
is compatible with your electrical
supply by checking the label on the
base of the unit.
16. Always place bottle into warmer
before adding water.
17. Ensure water has been added before
switching the unit on.
18. When the food has reached the
required temperature, remove
immediately. If left in the warmer,
the temperature of the food will
continue to increase.
19. The Electric Warmer is fitted with
a non-rewireable molded plug. The
mains supply cord of the appliance
CANNOT be replaced. If the cord
is damaged, the appliance should
be discarded.
20. This product is manufactured to
comply with the Radio Interference
Requirements and the EEC Directive
89⁄336⁄EEC.
4
21. A short power cord has been
provided to prevent the risk of it
becoming entangled or being
tripped over.
22. Extension cords may be used if care
is exercised in their use.
23. If an extension cord is used, its
electrical rating must be as great as the
rating of the appliance and not draped
over the edge of the table top where it
could be pulled by children or tripped
over. The extension cord should be a
grounded type 3 wire cord.
24. Failure to follow de-scaling instructions
may cause irreparable damage.
25. There are no serviceable parts inside
the Electric Warmer. Do not attempt
to open, service or repair the Electric
Warmer yourself. For assistance call
1-800-54-AVENT (1-800-542-8368).
26. Before serving, unplug cord from
wall outlet. Do not leave cord
within child's reach.
27. HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
Philips AVENT Electric Bottle and Baby Food Warmer
Instructions for use
For AVENT Natural Feeding Bottles
1. Ensure basket is in place inside the warmer.
2. Place the assembled, filled bottle in the
warmer with the dome cap removed.
3. For 4oz ⁄ 125ml bottles, fill the warmer
with water to just above the level of milk
in the bottle.
4. For larger bottles, fill the warmer to
15mm (1⁄2 inch) below the rim of
the warmer.
5. Never let the water level rise above the
neck of the bottle or spill over the edge
of the warmer.
6. Plug the unit into an electrical outlet and
click the switch to the ON position (I),
the neon light will illuminate. Turn the dial
to setting 3.
7. When the bottle has been in the warmer
for the appropriate time (See guide), the
light will flash on and off intermittently
to indicate that the water surrounding
the bottle is being kept at a constant
temperature.
8. Remove immediately. Replace the
dome cap. Shake the bottle and test the
temperature of the liquid by sprinkling
a few drops onto the back of your hand.
Please ensure the lid of the container is
tightly secured prior to shaking.
9. If the food is not ready, replace the
bottle in the warmer. TAKE CARE NOT
TO OVERHEAT. The water surrounding
the bottle will be kept at a constant
temperature but the temperature of the
food will continue to increase. If the food
is too hot, allow to cool. Always test
temperature before feeding.
10. Once the bottle has reached the correct
temperature and has been removed from the
unit, switch off warmer (O) and unplug from
the electrical outlet.
Note: The basket can be removed when
heating the AVENT Magic Cup and other
makes of bottles.
For the AVENT Tempo Natural Feeding
Nurser
1. Ensure basket is in place inside the warmer.
2. Place the assembled, filled Tempo Nurser in
the warmer with the dome cap removed.
3. Fill the warmer with water to the level
of milk in the bottle liner.
4. Plug the unit into an electrical outlet
and click the switch to the ON position
(I). The neon light will illuminate.
Turn the dial to setting 2 and continue
as 7–10 above.
Note: When using Tempo liners please
ensure that you choose the correct settings
as using a higher selection may cause liners
to burst.
EN
5