Fixing To The Wall; Fixing The Decorative Telescopic Flue; Filtering Version; Use And Maintenance - SCHOLTES HSB 308 IX NA Manual De Utilización

Use and maintenance

INSTALLATION INSTRUCTIONS
GB
OPERATING INSTRUCTION
READ AND SAVE THESE IN-
STRUCTIONS
GENERAL
• Carefully read the following important information
regarding installation safety and maintenance. Keep
this information booklet accessible for further consul-
tations.
The appliance has been designed for use in the ducting
version (air exhaust to the outside – Fig.2).
- control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to
the network and the socket is suitable. If in doubt ask
a qualified electrician (Fig.3).
INSTALLATION INSTRUCTIONS
• Power Supply Connection
For connection to the power supply refer to the follows
fig.12:
BLACK
WHITE
GREEN / YELLOW
A double-pole switch properly rated must be installed to
provide the range hood power supply disconnection.
The appliance must be installed at a minimum height
of 26 inches (66 cm) from an electric cooker stove, or
30 inches (76 cm) from gas or combined cooker stoves.
If a connection ductwork composed of two parts is
used, the upper part must be placed outside the lower
part. Do not connect the range hood exhaust duct air
to the same duct air used to exhaust hot air or fumes
from other appliances other than electrical. Before
proceeding with the assembly operations, remove the
anti-grease filter(s) (Fig.9) so that the unit is easier to
handle.
WARNING - TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS, OB-
SERVE THE FOLLOWING: Before making electrical
connections to power supply, the electrical box
must be secured in place as indicated in fig.1
Before installing the appliance fix the electrical box
as indicated in fig.1
- Remove the central screw fig.1A.
- Lift the electrical plant box fig. 1B.
- Remove the 3 fixed screws fig.1C.
- Position the electrical box so it is in line with the
holes of the previously removed screws fig.1D and
tighten.
10
= L line
= N neutral
= G ground
- Pay attention that the tear tape of the electrical box
is inside the slot
and then tighten screw fig.1E.

• FIXING TO THE WALL

Drill the holes A respecting the distances indicated
(Fig.4). Fix the appliance to the
wall and align it in horizontal position to the wall units.
When the appliance has been adjusted, definitely fix
the hood using the screws A (Fig.7). For the various
installations use screws and screw anchors suited to
the type of wall (e.g. reinforced concrete, plasterboard,
etc.). If the screws and screw anchors are provided with
the product, check that they are suitable for the type of
wall on which the hood is to be fixed.

• FIXING THE DECORATIVE TELESCOPIC FLUE

Take care not to scratch the duct; wear gloves when re-
moving the protective film (Fig.5). Arrange the electrical
power supply within the dimensions of the decorative flue.
If your appliance is to be installed in the ducting version or
in the version with external motor, prepare the air exhaust
opening. Adjust the width of the support bracket of the up-
per flue (Fig.6). Then fix it to the ceiling using the screws
A (Fig.6) in such a way that it is in line with your hood
and respecting the distance from the ceiling indicated
in Fig.4. Connect the flange C to the air exhaust hole
using a connection pipe (Fig.4). Insert the upper flue
into the lower flue. Extract the upper flue up to the
bracket and fix it with the screws B (Fig.6).

• FILTERING VERSION

Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version.
To assemble the filtering flue refer to the instructions
contained in the kit. If the kit is not provided, order it
from your dealer as accessory. The charcoal filters
must be fitted in the ducting unit located inside the
hood (Fig.8).
• If the apparatus is equipped with the following con-
trols (fig.11):
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes
• If your appliance does have the INTENSIVE speed
function, press key E for two seconds and it will be activated
for 10 minutes after which it will return to the previously
set speed.
When the function is active the LED flashes. To interrupt
it before the 10 minutes have expired press key E again.