Matco Tools MT2816 Instrucciones De Operación página 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION
IMPORTANT SAFETY INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• It is the responsibility of the owner to make sure all
personnel read this manual prior to using the device .
It is also the responsibility of the device owner to keep
this manual intact and in a convenient location for all to
see and read. If the manual or product labels are lost or
not legible, contact Matco Tools for replacements. If the
operator is not fluent in English, the product and safety
instructions shall be read and discussed with the operator
in the operator's native language by the purchaser/
owner or his designee, making sure that the operator
comprehends its contents .
• Always operate, inspect and maintain this tool in
accordance
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations .
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig 6.2 bar max
air pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face protection
when operating or performing maintenance on this tool,
users and bystanders.
• Always wear hearing protection when using this tool, users
and bystanders. High sound levels can cause permanent
hearing loss . Use hearing protection as recommended by
your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if discomfort,
tingling feeling or pain occurs. Seek medical advice
before resuming use.
• Air under pressure can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach tool
from air
adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure to
do so could result in injury. Whip hoses can cause
serious injury. Always check for damaged, frayed
or loose hoses and fittings, and replace immediately.
Do not use quick detach couplings at tool . See
instructions for correct set-up.
• The tool must be placed the tool on the work before starting
the tool .
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool .
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
MT2816
MT2816 Long Barrel Air Hammer
MANUAL
with American National
and maintenance personnel
supply before installing, removing
WARNING
CONTAINS
Standards
must be
or
2
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool chisel shank may continue to move briefly after trigger is
released . Avoid direct contact with accessories during and
after use. Gloves will reduce the risk of cuts or burns
• Keep hands away from the end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories .
• Never use a chisel as a handstruck tool. They
are designed and heat treated to be used only in air
hammers . Select the correct shank and retainer
for the tool.
• Never use dull, chipped
accessories. Never cool
water as brittleness and early failure can result. Accessory
breakage or tool damage may result from prying. Take smaller
bites to avoid getting stuck .
• Never operate the tool without a Chisel Retainer.
• Use accessories recommended by Matco Tools.
• Do not lubricate tools with flammable or volatile liquids such
as kerosene, diesel or jet fuel.
• This tool must not be used in explosive atmospheres.
• This tool is not insulated against electric shock.
• Keep away from children.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• Do not use (or modify) the tool for any other purpose than
that for which it was designed without consulting the
manufacturer's authorized representative.
• This product may contain one or more chemicals known to
the State of California to cause cancer and birth defects or
other reproductive harm . Wash hands thoroughly
after handling.
or damaged
a hot accessory in
Rev. 05/02/14