Ego Power+ BCX3800 Manual De Usuario página 7

17. Outer Flange
EN
18. Nut
19. Multi-function Wrench
20. Hex Wrench
21*. Hip-pad (Sold separately)
WARNING:
Never operate the tool without the guard
firmly in place. The guard must always be on the tool to
protect the user.
WARNING:
When the tool is equipped with a
trimmer head, the guard accessory with line–cutting
blade should be mounted onto the guard. Failure to
comply will result in overly long cutting line and overload
the motor. Never use the trimmer head without guard
accessory.
ASSEMBLY
WARNING:
If any parts are damaged or missing, do
not operate the brush cutter until the parts are replaced.
Use of the brush cutter with damaged or missing parts
could result in serious personal injury.
WARNING:
Do not attempt to modify the brush
cutter or create accessories not recommended for use
with this product. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possibly serious personal injury.
WARNING:
Always wear heavy gloves when
installing or removing the guard and doing any
maintenance on the 3-teeth blade/line-cutting blade.
Be careful of the line-cutting blade on the guard
accessory / 3-teeth blade for protecting your hands from
being injured by both the blades.
WARNING: To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
WARNING: Never operate the tool without the guard
and bike handle firmly in place. Failure to comply could
result in possible serious personal injury.
MOUNTING AND ADJUSTING THE BIKE HANDLE
The brush cutter is stored as shown in Fig. B. Firstly,
loosen the wing bolt on the connecting joint and then lift
the bike handle 180° around the shaft (Fig. C), turn it 90°
anticlockwise to make it face the bump head (Fig. D).
Lastly, move it back and forth to achieve a comfortable
working position and tighten the bolt.
12
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BCX3800
NOTICE:
Operating the machine with the bike handle
perpendicular to the shaft is only permitted.
MOUNTING THE GUARD
Loosen and remove the two screws from the guard (Fig. E),
align the guard mounting holes with the assembly holes and
then lock the guard onto the shaft base with the two screws,
together with two spring washers (Fig. F).
WARNING: Make sure the guard is fixed according
to Fig. F & G, any reverse fixing will cause great danger!
WARNING:
When the brush cutter is equipped with
a trimmer head, the guard accessory must be mounted
onto the guard. Failure to comply could result in an
overly long cutting line and motor overload.
REPLACE THE TRIMMER HEAD WITH THE 3-TEETH
BLADE
Know the trimmer head as Fig. G shown. Then disassemble
the trimmer head and mount the 3-teeth blade on the brush
cutter.
1. Press the release tabs on the spool retainer and remove the
spool retainer by pulling it straight out (Fig. H1 & H2).
2. Rotate the upper housing assembly to align the slot in
the flange with the shaft-locking hole in the gear case
and insert a stabilizer into the hole (Fig. H3).
3. Rotate the socket wrench clockwise to remove the nut
and upper housing assembly (Fig. H4).
4. Remove the guard accessory by loosening the three
screws with washer (Fig. H5).
5. The blade is shipped with a sheath. Before mounting
the blade onto the brush cutter, the sheath should be
removed by undoing the clamp wire from the hook on
the sheath (Fig. I1).
Fig. G & I1 parts description see below:
G-1 Inner Flange G-6 Cutting Line
G-2 Flange Cover G-7 Spool Retainer
G-3 Upper Housing ASSY G-8 Lower Housing ASSY
G-4 Nut I-1 Clamp Wire
G-5 Spring I-2 Hook
NOTICE: To protect against injury, you have to wear
gloves prior to any operation with the 3-teeth blade.
6. Mount the inner flange and flange cover into its place
(Fig. I2).
7. Mount the blade onto the motor shaft, ensuring that the
surface of the blade is flush with the surface of the inner
flange bulge. Mount the outer flange and the nut (Fig. I3).
Pre-tighten the nut in a COUNTERCLOCKWISE direction
by hand.
8. Position the gear case against a solid surface for support.
With one hand hold the brush cutter shaft and the other
hand grasp the multi-function wrench to tighten the nut
following the directional arrow icon marked on the outer
flange (Fig. I4).
REPLACE THE 3-TEETH BLADE WITH THE TRIMMER
HEAD
Know the 3-teeth blade cutting unit as Fig. J1 shown. Then
disassemble 3-teeth blade and mount the trimmer head on
the brush cutter.
1. Rotate the blade to align the slot in the flange with
the shaft-locking hole in the gear case and insert a
stabilizer into the hole.
2. Position the gear case against a solid surface for
support. With one hand hold the brush cutter shaft
and the other hand grasp the multi-function wrench
to loosen the nut clockwise.
3. Take out the nut, outer flange, blade, inner flange
cover and inner flange from the brush cutter (Fig. J2).
Fig. J1, J3 & J7 parts description see below:
J-1 Shaft J-6 Nut
J-2 Inner Flange J-7 Slot in the Flange
J-3 Flange Cover J-8 Spring
J-4 3-teeth Blade J-9 Notch
J-5 Outer Flange J-10 Eyelet
NOTICE:
When the 3-teeth blade is unused, to prevent
personal injury, mount the blade into its sheath.
4. Assemble the guard accessory to the brush cutter by
tighten three screws with washer.
5. Mount the lower housing onto the gear case by
tightening the nut and put the spring into its place
(Fig. J3).
6. Fold and wind trimmer line onto the spool as Fig. J4
shown. Then place the line ends through the two
opposite notches in the spool (Fig. J5) and place
the spool into its retainer with notches aligned with
retainer eyelets (Fig. J7). Lastly, align the retainer
slots with the tabs on the spool base and press the
retainer evenly down, ensuring that it snaps into
place (Fig. J6).
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BCX3800
NOTICE:
Failure to wind the line in the direction
indicated it will cause the trimmer head to operate
incorrectly.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection, along with
hearing protection. Failure to do so could result in objects
being thrown into your eyes and other possible serious
injuries.
WARNING: Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
HOLDING THE BRUSH CUTTER
Before connect the backpack battery with the brush
cutter, wear your backpack battery and mount the hip-
pad your backpack harness referring to BAX1500 and
AHP1500 manual.
Mount the brush cutter with your hip-pad by connecting
the hook to the mounting hole (Fig. K). There are 8 holes
upon the shaft, choosing an optimum hole for comfortable
operation.
Hold the line trimmer with both hands on the right side of
your body. The trimmer head or blade should be parallel to
the ground at a proper cutting distance without the operator
bending over.
Releasing the brush cutter can be achieved in two ways.
Release the chest and belt buckles (Fig.L1) or press the
hook of the hip-pad and take it apart from the mounting
hole on the shaft.
WARNING:
When emergency occurs, releasing the
chest and belt buckles is the quick release method to
release the brush cutter.
WARNING: You should not use the single-shoulder
strap and double-shoulder strap with backpack battery
simultaneously.
To Install Battery Pack (Fig. L2)
Align ▲ of plug with ▲ of brush cutter. Insert the plug into
the machine until the green seal completely disappeared
into the socket.
13
EN