Energizer Power & Play Flat Panel 2X Guía De Inicio Rápida

Thank you for purchasing the Energizer® Power & Play™ Flat Panel 2X
Induction Charging System for Wii Remotes.
Contents
1 Flat Panel 2X Induction Charging Base for Wii Remotes
2 Rechargeable battery packs for Wii Remotes / battery door units
1 AC power cord
Using the Charging System
1) Plug the smaller end of the AC cord into the back of the charge dock and plug the other end into an AC
outlet.
2) Remove standard AA batteries from your Wii Remote. Next, insert the Induction Battery Pack / battery
door unit into your Wii Remote. (If you are using Wii Remote Jacket or other sleeve on your Wii Remote,
you must first remove it.)
3) If you must sync your Wii Remote to your Wii Console upon your first use of the Energizer® Induction
Battery Pack, press the small button above the Energizer logo on the Induction Battery Pack. This will
activate the Wii Remote's sync functionaltiy. Afterwards, press the sync button on your Wii console.
4) Replace the Wii Remote Jacket on your Wii Remote. Induction technology allows energy to transfer
through the Jacket wirelessly
5) Attach Wii MotionPlus add-on to Wii Remote if desired. The Energizer® Flat Panel Induction Charging
System for Wii can charge Wii Remotes with or without the MotionPlus add-on and Silicone Jacket
attached.
A
6) Look for the Wii Remote outlines on the surface of the Energizer® Flat Panel Induction Charger and then
place your Wii Remote on the surface accordingly, so that it lines up with one of the outlines (the Wii
Remote's camera should face the Energizer® logo on the charger.)
Flat Panel 2X Induction Charging System
A
7) Magnets in the Energizer® Flat Panel Induction Charger will help ensure a perfect charging position. Take
note of the attraction you feel when placing the Wii Remote on the Flat Panel Induction Charger and let
the magnets guide the Wii Remote to optimal placement.
8) When charging begins the charge indicator lights for each Wii Remote charging position will shine near
the Energizer® logo on the Energizer® Flat Panel Induction Charger. Red indicates charging is in progress. `
Green indicates that charging is complete.
Frequently Asked Questions
Can I charge my Wii Remote with the Wii Remote Silicone Jacket attached?
- Yes. Induction technology allows charging through the Silicone Jacket.
Can I charge my Wii Remote with a Nintendo MotionPlus attached?
- Yes. The MotionPlus and the MotionPlus Silicone Jacket do not interfere with charging. This is one of the great benefits of Induc-
tion Technology.
Can I use my Wii Remote if the charge indicator light is red?
- Yes. Your Induction Battery pack may not be fully charged if the charge indicator light is red when you remove the Wii Remote, but
this will not harm the battery. If your Wii Remote runs out of charge, simply return it to the Energizer® Flat Panel Induction Charger
for more charging.
Can I leave my Wii Remote on the charge dock after the charge light turns green?
- Yes. The Energizer® Flat Panel Induction Charger features trickle charging technology that ensures your Induction Battery Pack is
never over-charged and will remain ready to play at all times.
The charge light went from green to red when I removed my Remote for just a minute – can I still use it?
- Yes. Communication takes place between the Induction Battery Pack and the Energizer® Flat Panel Induction Charger. If the
Induction Battery Pack is fully-charged when placed on the Induction Charger, the charge indicator lights will change from red to
green in a few moments.
How long will it take to charge the battery pack(s)?
- Approximately 4-hours from a fully discharged condition.
My Induction Battery Pack feels a little warm after charging. Is this a problem?
- No. A small degree of heat dissipation is a natural byproduct of the Induction Charging process. The heat should be no more than
you might feel after charging a cell phone or laptop computer.
Can I use the Energizer® Flat Panel Induction Charger to charge other batteries?
- No. The Energizer® Induction Base is only intended for charging Energizer Remote Induction rechargeable battery packs for Wii
Remotes. Standard battery packs lack Induction Technology required for the Energizer® Flat Panel Induction Charger to function.
Can I use the AC cord on other appliances?
- No, this AC cord is to be used only with the Energizer® Flat Panel Induction Charger.
Care and Maintenance
Keep away from extreme temperatures and humidity, including direct sunlight.
Never submerge any parts of the product in liquid.
To clean, wipe gently with a soft dry cloth.
Store in a cool, dry place when not in use.
Opening the charging dock will automatically void the warranty.
WARNING: Charge only Energizer® NiMH Battery packs in this Charging System for Wii Remotes. Charging any other types of
batteries or battery packs may cause them to leak, rupture or explode. Do not open battery, dispose of in fire, put in backwards,
mix with used or other battery types or short circuit – may ignite, explode, leak or get hot causing injury.
*See manufacturer's manual and follow all instructions and warnings for use of Wii Remotes.
For technical questions please visit
www.pdp.com or call: 1-800-331-3844
Energizer and other marks are trademarks of Eveready Battery Company, Inc. and are used by Performance Designed Products LLC under license. All other brand names
are trademarks or registered trademarks of their respective owners. Neither Performance Designed Products LLC nor Eveready Battery Company, Inc. is affiliated with the
respective owners or their trademarks. This product is not designed, manufactured, sponsored or endorsed by Nintendo of America, Inc.
For Nintendo Wii®
For:
PL-7581
A
A