Pella Designer Serie Guia De Inicio Rapido

BLINDS AND SHADES
Designer Series
This Quick Start Guide is intended only to provide an overview
of the product and its use. Before using this product, read the
complete Product Guide and warnings.
Scan the QR Code
for complete Product Guide and warnings, instructional videos
and other Pella
WHAT'S INCLUDED:
• PELLA DESIGNER SERIES BLINDS OR SHADES WITH
INSYNCTIVE TECHNOLOGY
• QUICK START GUIDE
WHAT'S NEEDED:
• PELLA INSYNCTIVE SINGLE-CHANNEL REMOTE (sold separately)
or smart device with compatible Z-Wave home automation system
and the Insynctive BRIDGE.
• PELLA INSYNCTIVE WALL CHARGER (optional — sold separately)
1. Get Started
See Insynctive.Pella.com/Support for how-to videos.
• To unpack BLIND or SHADE, open the Hinged Glass
Panel (HGP) and remove the cardboard corner
protectors and bands that secure BLIND or SHADE.
HINGED
GLASS • Check to make sure that the wire is firmly seated
PANEL
in the groove by the HGP gasket. Press any loose
(HGP)
portions of the clip back into the groove in the HGP.
• Close the HGP and ensure that it is securely latched.
• REMOTE ships in a separate package. Unpack
REMOTE. To set up REMOTE, follow Remote
SOLAR
Quick Start Guide or Remote Product Guide, or visit
PANEL BATTERY
Insynctive.Pella.com/Remote for more information.
2. Set Up BLIND or SHADE
Complete the following steps to set up BLIND or SHADE.
• Locate the wire that runs from the BLIND or SHADE
VIEW WITH HGP OPEN
cover to the battery at the bottom of the unit. For
BLIND OR casement windows, sliding patio doors and hinged
SHADE
patio doors, the wire will be located on the same
COVER
side as the HGP latch releases. For double-hung or
Precision Fit
HGP
LATCH
located on the right-hand side of the unit.
RELEASE
• With the HGP closed, touch the top end of
WIRE
REMOTE to BLIND or SHADE cover approximately
6" from the edge of the glass on the side where the
wire is connected. Move REMOTE back and forth
VIEW WITH HGP CLOSED
slowly until BLIND or SHADE completes a quick
up/down motion to indicate BLIND or SHADE has
entered sync mode.
COVER
• Press and hold Up button on REMOTE until BLIND
or SHADE completes a quick up/down motion. This
REMOTE
will require the Up button to be pressed for about
MEASURE 6"
3 seconds.
FROM END WHERE
WIRE CONNECTS
• Press and release the Down button to send BLIND or
SHADE to its lower position. If you would like to change
this position, follow the procedure for Programming the
Lower Position in the Product Guide.
Between-the-Glass
®
QUICK START GUIDE
or visit Insynctive.Pella.com/DesignerSeries
®
® Insynctive ™ quick tips.
window units, the wire will always be
®
LED
LIGHT
• Press and release the Center button to send BLIND or
UP
SHADE to its user position. The user position is set by
BUTTON
the factory at approximately 50% of the distance between
CENTER
BUTTON
the fully opened and fully closed position. If you would
DOWN
like to change this position, follow the procedure for
BUTTON
Programming the User Position in the Product Guide.
• Press and release the Up button to send BLIND or SHADE to its
upper position. If you would like to change this position, follow the
procedure for Programming the Upper Position in the Product Guide.
• BLIND or SHADE is now ready for use.
HAVE A HOME AUTOMATION OR SECURITY SYSTEM?
For instructions on how to sync Pella
Insynctive.Pella.com/HomeAutomation.
NEED HELP WITH THE STEPS ABOVE?
Find troubleshooting information and videos at Insynctive.Pella.com/Support
or call 855-473-5524.
WANT TO EASILY REGISTER PELLA INSYNCTIVE PRODUCTS?
Visit Insynctive.Pella.com/Registration for instant access to instructions,
warranties and how-to videos.
WARNING
Failure to adhere to the warnings below may result in death, serious injury and/or
loss of valuables.
• Pella Insynctive products are not 100% reliable for a variety of reasons (see
Product Guide for more information). Therefore, Pella Insynctive products
should not be relied upon in situations where life, safety and/or protection of
valuables are solely dependent on their function. Test each product at least
once per year to help ensure proper operation.
• BRIDGE may be connected to a non-Pella product, such as a compatible
security or home automation system. All systems are subject to compromise
or failure to warn for a variety of reasons. Review and comply with the informa-
tion for the system that BRIDGE is connected with.
• Pella Insynctive products are not a substitute for careful adult supervision
of children.
• Keep small parts out of reach of children. If swallowed, immediately seek
medical help.
Read the complete Product Guide for additional warnings and information.
FCC Compliance and Industry Canada
This equipment has been tested and found to comply with the limits for Class B
digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit from the receiver.
• Consult the dealer or an experienced radio/TV contractor for help.
Changes or modifications not expressly approved by Pella Corporation could
void the user's authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard
RSS. L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne
peut causer d'interférences, et (2) cet appareil doit accepter toute interférence,
y compris les interférences qui peuvent causer un mauvais fonctionnement de
l'appareil.
FCC ID: SO7-206B0000
IC: 11009A-206B0000
Insynctive products to it, visit
® ™
© 2014 Pella Corporation
81QX0100
IDSPG1014