Matco Tools MT2875R Instrucciones De Operación página 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION MANUAL CONTAINS IMPORTANT
SAFETY INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY AND
UNDERSTAND ALL INFORMATION BEFORE OPERATING
THIS TOOL.
• It is the responsibility of the owner to make sure all personnel
read this manual prior to using the device . It is also the
responsibility of the device owner to keep this manual intact and
in a convenient location for all to see and read . If the manual
or product labels are lost or not legible, contact Matco Tools
for replacements . If the operator is not fluent in English, the
product and safety instructions shall be read and discussed
with the operator in the operator's native language by the
purchaser/owner or his designee, making sure that the operator
comprehends its contents .
• Always operate, inspect and maintain this tool in accordance
with American National Standards Institute Safety Code of
Portable Air Tools (ANSI B186 .1) and any other applicable safety
codes and regulations .
• For safety, top performance and maximum durability of parts,
operate this tool at 90 psig; 6 .2 bar max air pressure with 3/8"
diameter air supply hose .
• Always wear impact-resistant eye and face protection when
operating or performing maintenance on this tool (users and
bystanders) .
• Always wear hearing protection when using this tool . High
sound levels can cause permanent hearing loss . Use hearing
protection as recommended by your employer or OSHA regulation
(users and bystanders) .
• Keep the tool in efficient operating condition .
• Operators and maintenance personnel must be physically able
to handle the bulk, weight and power of this tool .
• Air powered tools can vibrate in use . Vibration, repetitive
motions or uncomfortable positions over extended periods of time
may be harmful to your hands and arms . Discontinue use of tool if
discomfort, tingling feeling or pain occurs . Seek medical advice
before resuming use .
• Air under pressure can cause severe injury . Never direct air
at yourself or others . Always turn off the air supply, drain hose
of air pressure and detach tool from air supply before installing,
removing or adjusting any accessory on this tool, or before
performing any maintenance on this tool . Failure to do so could
result in injury . Whip hoses can cause serious injury . Always
check for damaged, frayed or loose hoses and fittings, and replace
immediately . Do not use quick detach couplings at tool . See
instructions for correct set-up .
• Slipping, tripping and/or falling while operating air tools can be
a major cause of serious injury or death . Be aware of excess hose
left on the walking or work surface .
• Keep body working stance balanced and firm . Do not overreach
when operating the tool .
• Anticipate and be alert for sudden changes in motion during
start up and operation of any power tool .
• Do not carry tool by the hose . Protect the hose from sharp
objects and heat .
• Tool shaft may continue to rotate briefly after throttle is
released . Avoid direct contact with accessories during and after
use . Gloves will reduce the risk of cuts or burns .
• Keep away from rotating end of tool . Do not wear jewelry or
loose clothing . Secure long hair . Scalping can occur if hair is
MT2875R, MT2875RG, MT2875RM
MT2875R 3" FLEX HEAD CUT-OFF TOOL
WARNING
not kept away from tool and accessories . Choking can occur if
neckwear is not kept away from tool and accessories .
• Use accessories recommended by Matco Tools .
• Do not operate a damaged or worn tool . Do not use
quick-detach couplings at tool . See instructions for correct set-up .
• RPM OF THE ACCESSORY MUST EXCEED TOOL RPM. Use
RPM RPM RPM
accessories rated at 20,000 RPM or higher.
• Do not lock, tape or wire the "on/off" safety lever in the "on"
position, as the lever must be free to return to the "off" position
when released.
• Correct cut-off wheel mounting is necessary to prevent injury
from broken wheels . Do not use chipped or cracked cut-off
wheels . Cut-off wheels should be a free fit on the spindle to
prevent stress at the hole . Use only wheel collars that come with
the tool for mounting the cut-off wheel . Flat washers or other
adapters may over stress the wheel . Tighten the cut-off wheel on
the spindle to prevent spin off when the tool is turned off .
• NEVER OPERATE THIS TOOL WITHOUT THE REQUIRED DISC
COVER/GUARD IN PLACE.
• When using the cut-off tool, be careful not to exert excessive
force . Too much force could be hazardous if it causes the
tool spindle to bend or break . The burning of the work piece
or excessive speed reduction indicates too much force being
applied . Start the tool off the work, set it down on the work evenly
and move in the direction desired to make the cut . When finished
cutting, lift off the work before stopping the motor .
• Do not lubricate tools with flammable or volatile liquids such as
kerosene, diesel or jet fuel .
• Do not force tool beyond its rated capacity .
• Do not remove any labels . Replace damaged labels .
• This tool is not insulated against electric shock .
• Keep tool out of reach of children .
• Do not point or indulge in any horseplay with this tool .
• Note direction of rotation BEFORE operating this tool .
• This tool must not be used in explosive atmospheres .
• Do not use (or modify) the tool for any other purpose than that
for which it was designed without consulting the manufacturer's
authorized representative .
• Servicing and repairs should only be made by an authorized
service center .
• Failure to heed these warnings may result in personal injury
and/or property damage .
WARNING: This product can expose you to chemicals
including phthalates, which is known to the State of California
to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
2 08/28/19