Descargar Imprimir esta página

Air Supply - Matco Tools MT1650 Instrucciones De Operación

Publicidad

Idiomas disponibles

Idiomas disponibles

air supply

Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI
at the tool while running free. Higher pressure and unclean air
will shorten tool life because of faster wear and may create a
hazardous condition.
Water in the air line will cause damage to the tool. Drain the
air tank daily. Clean the air inlet filter screen on at least a weekly
schedule. The recommended hook-up procedure can be viewed
in Figure 1.
The air inlet (Figure 2), used for connecting air supply, has standard 1/4" NPT
American Thread.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D. and
fittings should have the same inside dimensions.
Whip Hose
Do Not Install
Quick Coupling
Nipple
Here
Leader
Quick Coupler
Hose
WarranTy
Matco warrants its air tools for a period of 1 year to the consumer. We will
repair any MT Series air tool covered under this warranty which proves to
be defective in material or workmanship during the warranty period. In order
to have your tool repaired, return the tool to either of the Matco Authorized
Warranty Centers listed below, freight prepaid. Please include a copy of your
proof of purchase and a brief description of the problem. The tool will be
inspected and if any part or parts are found to be defective in material or
workmanship, the tool will be repaired free of charge and returned to you
freight prepaid.
This warranty gives you specific rights. You may also have other rights which
vary from state to state.
The foregoing obligation is Matco's sole liability under this or any implied
warranty and under no circumstances shall Matco be liable for any incidental
or consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may
not apply to you.
MT1650
MT1650 .50 HP POLISHER
feaTures
• High performance efficient 1/2 HP motor for extra torque and extended durability
• Industrial Cut Gear design to 1,800 RPM no load speed - perfect for all kinds of polishing
• Ideal for jobs like polishing bumpers, corners and much more
• Adjustable rear exhaust to direct air away from the work and away from the user
• Positive stop regulator for more versatile performance on all kinds of jobs
• Super comfortable safety throttle lever to prevent accidental start ups
• Convenient side handle for total control in all kinds of positions
Filter
Nipple
Oiler
Regulator
TrouBleshooTing
Other factors outside the tool may cause loss of power or
erratic action. Reduced compressor output, excessive drain on
the air line, moisture or restrictions in air pipes or the use of hose
connections of improper size or poor conditions may reduce air supply. If
outside conditions are in order, and the tool still performs erratically, disconnect
tool from hose and take tool to your nearest Matco authorized service center.
luBricaTion & MainTenance
Lubricate the tool daily with a good grade of air tool oil. If no
air line oiler is used, run a teaspoon of oil through the tool. The oil can
be squirted into the tool air inlet Figure 2, or into the hose at the nearest
connection to the air supply, then run the tool. A rust inhibitive oil is acceptable
for air tools.
air inleT
Air Supply
Drain Daily
fig. 1
3
MaTco air coMMand
Tool Repair SV
1330 Commerce Dr.
Stow, OH 44224
(800) 433-7098
discounT Tool repair
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
fig. 2
12/12/05

Publicidad

loading