Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

OPErATING INSTruCTIONS ANd PArTS BrEAkdOwN
MOdEl 520-3001
SPECIFICATIONS
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Ton
Lifting Range . . . . . . . . . . . . . . . . . . . . 10-1/4" - 19-3/4"
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 c.c.
Jack Size . . . . . . . . . . . . . . . . . . . 22-3/4" x 10-7/8" x 50"
PSI Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Shipping Wt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71.5 Lbs.
FEATurES
• Chrome Plated Lift Ram
• Self-Retracting Ram Springs for Fast Ram Retraction
• Push valve Lever for Fast Air Control
• 3 Position Lock Lever
• Safety Overload valve
• Large Diameter Wheels for ease of Operation
OPErATING INSTruCTIONS
IMPOrTANT: Before attempting to raise a vehicle,
check vehicle service manual for recommended
lifting surfaces.
1. To raise load: Close release valve tightly (by turning
release knob on handle clockwise) DO NOT OveR-
TIGHTeN. Position jack under load so that saddle will
contact load firmly and load is centered so it cannot
slip. Operate air valve until saddle approaches the
load. Once again check to see that saddle is correctly
positioned. Raise load to desired height. Place jack
stands of appropriate capacity under the vehicle. DO
NOT CRAWL UNDeR veHICLe WHILe LIFTING veHI-
CLe OR PLACING OR ReMOvING JACK STANDS! Place
jack stands at vehicle manufacturer's recommended
lift areas that provide stable support for the raised
vehicle. Slowly turn the release valve knob counter-
clockwise to lower the vehicle onto the jack stands.
Lower the vehicle slowly so as not to shock load
the jack stands. Once repairs are completed, raise
vehicle enough to remove jack stands. Lower vehicle
very slowly.
2. To lower load: Open Release valve veRY SLOWLY
(by turning release valve knob on handle counter-
clockwise.) When release valve is opened, saddle
and load will be lowered.
Rev. 10/19/00
20 Ton Air/Hydraulic Service Jack
This operaTing manual conTains
imporTanT safeTy informaTion.
read carefully and undersTand all
informaTion before operaTing Tool.
save This manual for fuTure use.
This is a LifTing Device OnLY. DO nOT MOve Or DOLLY The vehicLe WhiLe
On The Jack. iMMeDiaTeLY afTer LifTing sUPPOrT The vehicLe WiTh
aPPrOPriaTe Means.
DO nOT OverLOaD. OverLOaDing can caUse DaMage TO Or faiLUre Of
The Jack.
LifT OnLY On areas Of The vehicLe as sPecifieD bY The vehicLe ManU­
facTUrer.
cenTer LOaD On saDDLe PriOr TO LifTing. Off­cenTer LOaDs MaY caUse
DaMage TO Jack, LOss Of LOaD, PrOPerTY DaMage, PersOnaL Or faTaL
inJUrY.
This Jack is DesigneD fOr Use OnLY On harD LeveL sUrfaces caPabLe
Of sUsTaining The LOaD. Use On OTher Than harD LeveL sUrfaces can
resULT in Jack insTabiLiTY anD POssibLe LOss Of LOaD.
nO aLTeraTiOns TO The Jack shaLL be MaDe.
reaD, sTUDY anD UnDersTanD The OPeraTing ManUaL PackeD WiTh This
Jack befOre OPeraTing.
faiLUre TO heeD These Warnings MaY resULT in LOss Of LOaD, DaMage
TO Jack, anD/Or faiLUre resULTing in PrOPerTY DaMage, PersOnaL Or
faTaL inJUrY.
FOr YOur SAFETY ANd TO PrEVENT INJurY:
Use Service Jack for
lifting purposes
Always support
1
ONLY.
vehicle with
jack stands.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Napa 520-3001

  • Página 1 Tool. save This manual for fuTure use. OPErATING INSTruCTIONS ANd PArTS BrEAkdOwN MOdEl 520-3001 20 Ton Air/Hydraulic Service Jack SPECIFICATIONS Capacity ....... . 20 Ton Lifting Range .
  • Página 2 PArTS BrEAkdOwN — 520-3001 Ton Air/Hydraulic Service Jack ASSEMBlY INSTruCTIONS This jack comes pre-assembled except for the handle. The handle is a 2 piece handle. Align the thru hole of the upper and lower piece, and insert 2 pieces M6 allen bolts.
  • Página 3 PArT NO. ITEM NO. dESCrIPTION QTY. *6620A-2 Cover *6620A-10 extension/Screw Assy. *6620A-17 Return Spring *6620A-19 Hydraulic Cartridge Assy. *6620A-24 Release valve *6620A-26 Flexible Joint Assy. *6620A-29 Rubber Wheel *6620A-37 Complete Air Motor Assy. 1 *6620A-38 Hose Assy. *6620A-41 Knob *6620A-50A Handle Assy.
  • Página 4: Possible Problems And Solutions

    INSPECTION visual inspection should be made before each use of the MAINTENANCE air/hydraulic service jack, checking for leaking hydraulic To Add Oil: With saddle fully lowered and ram depressed, fluid and damaged, loose or missing parts. each jack set jack in an upright position and remove oil filler plug. must be inspected by a manufacturer’s repair facility Fill until oil is level with filler plug hole.
  • Página 5 This warranty does not cover repairs made by anyone who is not a Balkamp/NAPA Lifting equipment Authorized Repair Center.
  • Página 6: Instrucciones Para El Funcionamiento Y Lista De Piezas

    ANTES dE PrOCEdEr CON El FuNCIONAMIENTO dE ESTE APArATO. CONSErVE ESTE MANuAl PArA TENEr uNA rEFErENCIA EVENTuAl. INSTruCCIONES PArA El FuNCIONAMIENTO Y lISTA dE PIEZAS 520-3001 Gato utilitario aire / hidráulico - Capacidad 18.1 toneladas métricas CArACTErÍSTICAS ADVERTENCIA • eje para soporte plaqueado con cromo •...
  • Página 7: Instrucciones Para El Ensamblado

    rESPONSABIlIdAd dEl PrOPrIETArIO/ ESPECIFICACIONES uSuArIO Capacidad ..... . 18.1 toneladas métricas Alcance de el propietario y/o usuario debe comprender las instrucciones levantamiento .
  • Página 8: Posibles Problemas Y Soluciones

    POSIBlES PrOBlEMAS Y SOluCIONES SOluCIONES La válvula de aflojamiento no se cierra correctamente. Gire la válvula firmemente en el sentido del reloj. el nivel de aceite puede ser bajo. Llene el gato hasta el nivel apropiado de aceite. el resorte de regreso está quebrado o las conexiones están forzadas. Reemplace el resorte si quebrado.
  • Página 9: Garantía - Información Napa

    Balkamp/NAPA, para el equipo de levantamiento. Los artículos siguientes tienen una garantía de cambio directo en la tienda por 180 días. el producto presumiblemente defectuoso, debe devolverse a Balkamp, provisto de un recibo, demostrando la prueba de la compra, por medio de una tienda de piezas automóviles NAPA.
  • Página 10 AVANT dE PrOCÉdEr Au FONCTIONNEMENT dE CET OuTIl. CONSErVEZ CE MANuEl POur rÉFÉrENCE ÉVENTuEllE. dIrECTIVES dE FONCTIONNEMENT ET lISTE dE PIÈCES MOdÈlE 520-3001 Cric utilitaire professionnel air / hydraulique - 18.1 tonnes métriques CArACTÉrISTIQuES • Arbre de support plaqué chromé...
  • Página 11: Directives D'assemblage

    SPÉCIFICATIONS-: rESPONSABIlITÉ du PrOPrIÉTAIrE / uTIlISATEur Capacité ......18.1 tonnes métriques Le propriétaire et / ou utilisateur doit posséder une Échelle de levage .
  • Página 12 COIN-dÉPANNAGE PrOBlÉMES ET SOluTION POSSIBlES SOluTION La valve de relâchement n’est pas fermée. Tournez fermement la valve dans le sens des aiguilles d’une montre Le niveau d’huile est bas. Remplissez le cric au niveau d’huile adéquat. Le ressort de retour est brisé ou les connexions sont forcées Remplacez le ressort s’il est brisé.
  • Página 13 Durant la période de garantie de 180 jours, tout produit et/ou pièce présumé défectueux doit être retourné, franc de port, muni d’une preuve de la date d’achat, au centre autorisé le plus proche pour la garantie Balkamp/NAPA, pour équipement professionnel de levage. assurez-vous d’inclure votre nom, adresse et numéro de téléphone, incluant les renseignements de preuve d’achat, ainsi qu’une brève description de la présumée défectuosité. Le...

Tabla de contenido