EarthQuaker Devices Afterneath Manual Del Usuario página 3

<<< Controls >>>
1
5
6
7
10
11
12
15
16
19
1
Input: Adjusts the level of the incoming signal to allow for signals ranging from instrument-
level (clockwise) to modular-level (counterclockwise).
2 Dampen: Controls the tone of the wet signal. Clockwise for darker tones, counterclockwise
for brighter tones.
3 Reflect: Controls the regeneration of the reverb, turn clockwise for more wash and echoes,
counterclockwise for less. This will self-oscillate if turned up high. Acts as an attenuator when
there is a signal patched into the Reflect Return jack.
4 Mix: Controls the amount of wet signal that is mixed with the dry signal. Though it does not
actually go completely wet, you can achieve a fully wet signal by engaging the Dry Kill switch.
5
Dry Kill: Eliminates the dry signal from the output, leaving only the wet signal.
4
2 3 4
20 21 22
Drag: This digital reverb is made up of a bunch of short delays. Drag separates the delay
6
lines creating a stuttering, pingy effect. This is the coolest control on the Afterneath. We
highly advise slowly turning (or modulating) this while you let notes ring out for a cool warped
speed effect. The effect is more delay-like as you turn it counter clockwise, and it is more
reverb-like as you turn it clockwise. You will achieve shorter delay times as you move the
control clockwise, and longer delay times when you turn the control counterclockwise. You
will notice a change in pitch when adjusting this control with sound present in the effects
buffer, or when the effect is self-oscillating.
7
Mode: Controls the behavior of the Drag control as well as how it responds to control voltage.
There are 9 different modes (see the following Modes section for explanations).
8
Diffuse: Smooths and diffuses the delay repeats. Sharper transients with more attack
counterclockwise, more ambient, reverb-like and washy as you turn it clockwise.
9 Length: Controls the decay length of the reverb.
10 Mode LED: Visually indicates the current mode.
11
Drag CV Inverting Attenuator: Attenuates or inverts the incoming CV. The CV is at unity
gain when the attenuator is fully clockwise, inverted when it is fully counterclockwise and the
8
CV is completely attenuated when the attenuator is in the 12 o'clock position.
9
12
Mode CV Inverting Attenuator: Attenuates or inverts the incoming CV. The CV is at unity
gain when the attenuator is fully clockwise, inverted when it is fully counterclockwise and the
CV is completely attenuated when the attenuator is in the 12 o'clock position.
13
Diffuse CV Inverting Attenuator: Attenuates or inverts the incoming CV. The CV is at unity
13
gain when the attenuator is fully clockwise, inverted when it is fully counterclockwise and the
14 CV is completely attenuated when the attenuator is in the 12 o'clock position.
14
Length CV Inverting Attenuator: Attenuates or inverts the incoming CV. The CV is at unity
gain when the attenuator is fully clockwise, inverted when it is fully counterclockwise and the
17
CV is completely attenuated when the attenuator is in the 12 o'clock position.
18
15
Drag CV Input: Allows modulation of the Drag control using external CV.
16 Mode CV Input: Allows modulation of the Mode control using external CV.
17
Diffuse CV Input: Allows modulation of the Diffuse control using external CV.
18
Length CV Input: Allows modulation of the Length control using external CV.
19 Audio Input: Accepts audio signals ranging from instrument-level to modular-level, using the
Input knob to adjust the level.
20 Reflect Send: Allows external patching and processing of the Reflect feedback path. Patching
from this output does not interrupt the internal feedback path.
21
Reflect Return: Allows return of the externally patched and processed Reflect feedback
path. Also, it can be used as an additional audio input if you wish to forgo the feedback.
The Reflect knob acts as an attenuator for the audio that is patched to this input. Please
note that processing of the Reflect feedback path can easily result in self-oscillation when
processing with effects such as distortion or a resonant filter. The Reflect knob can be
used to compensate for this factor. Patching a cable to this input will disconnect the internal
feedback path, but the Reflect Send will still be active.
22 Audio Output
5