Sunex Tools SX260A Instrucciones De Operación página 4

Operating Instructions • Warning Information • Parts Break­down
Air Supply...
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI at
the tool while running free. Higher pressure (over 90 psig; 6.2 bar)
raises performance beyond the rated capacity of the tool; which will
shorten tool life because of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water
in the air line will cause damage to the tool. Drain the air tank
daily. Clean the air inlet filter screen on a weekly schedule. The
recommended connection procedure can be viewed in the
above figure.
The air inlet used for connecting air supply, has standard 1/4" NPT.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions and
be tightly secured.
Limited Warranty...
sunex internAtionAl, inc. wArrAnts to its custoMers thAt the coMpAny's sunex tools
worKMAnship And MAteriAls.
Sunex International, Inc. will repair or replace its Sunex Tools
based upon the terms and conditions of the following described warranty plans attributed to that specific product. This product carries a ONE-YEAR warranty.
During this warranty period, Sunex Tools
other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made
by anyone other than Sunex Tools
warranty and under no circumstances shall we be liable for any incidental or consequential damages.
note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Return equipment or parts to Sunex Tools
evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools
which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools
still covered by a warranty plan.
shipping Address: sunex tools
Mailing Address: sunex tools
®
SX260A
SX260A_manual_031507.indd 4
branded products which fail to give satisfactory service due to defective workmanship or materials,
®
will repair or replace at our option any part or unit which proves to be defective in material or workmanship.
®
or its authorized warranty service centers. The foregoing obligation is Sunex Tools' sole liability under this or any implied
®
, or an authorized warranty service center, transportation prepaid. Be certain to include your name and address,
®
• 315 hawkins rd. • travelers rest, sc 29690
®
• p.o. box 4215 • greenville, sc 29608
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no air line
oiler is used, run a half ounce of oil through the tool. The oil can
be inserted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool.
Operation...
Locate center of new hole by using a center punch. Place drill bit
tip in punch mark. Hold drill square with work and start motor.
Apply steady, even pressure. Do not force. Too much pressure can
cause bit to break or over heat. Too little pressure will keep bit from
cutting and cause it to over heat.
Reduce pressure just before bit cuts through the work. When bit
has penetrated work and is spinning freely, take it from the work
while the motor is running, then turn off drill.
If the drill jams in the work, release throttle immediately. Disconnect
the drill before removing bit and determining cause of trouble. Do
not attempt to free the bit by starting and stopping the motor.
brAnded products Are free froM defects in
®
. This warranty gives you specific legal rights and you may also have other rights
®
products regardless of whether or not the product is
®
 Rev. 03/5/07
3/16/07 4:20:32 PM