Wahl KM Manual De Operación página 2

properly, after it has been dropped or damaged, or after it has been dropped into water.
5) Return the appliance to a service center for examination and repair.
6) Keep the cord away from heated surfaces.
7) Never operate this appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where
it is possible for the air openings to be blocked. Keep the air openings free of lint, hair, and similar objects.
8) Never drop or insert any object into any opening.
9) Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being
administered.
10) Do not use this appliance with a blade or attachment that has been damaged or broken, as it has the potential to
result in facial injury.
11) During use, do not place or leave the appliance where it is expected to be subject to damage by an animal, or
exposed to weather.
12) Keep the appliance dry.
13) The appliance is intended for trimming purposes only.
14) Cutting blades may become hot after prolonged use.
SAVE THESE INSTRUCTIONS
THIS CLIPPER WAS DESIGNED FOR COMMERCIAL USE
Facts about blades and oiling:
• Blades not only become dull from cutting hair – they are dulled by the abrasive particles on the hair, dirt, sand etc.
• Blades will not cut if abrasive particles are picked up and carried between the blades. These particles tend to hold the blades apart and cause chewing and
pulling instead of clean cutting.
• Oiling the blades performs two distinct functions:
1) Provides a low friction, very thin lubricant film between the cutting blades so that they can take a full cutting stroke without becoming hot from friction.
2) Flushes abrasive particles and hair out from between the blades.
Note: If you cut into dirt, immediately wash with oil to flush out.
WE STRONGLY RECOMMEND WAHL CLIPPER OIL AS A LUBRICANT.
Servicing of a Double-Insulated Appliance
A double-insulated appliance is marked with one or more of the following: The words "DOUBLE INSULATION" or "DOUBLE INSULATED" or double insulation
symbol (square within a square).
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance,
nor should a means for grounding be added. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done
only by qualified service personnel. Replacement parts must be identical to those parts being replaced. A double-insulated appliance is marked with the words
"DOUBLE INSULATED". The symbol " " may also be marked on the appliance.
Directions:
Turn unit on/off
Two Speed:
• Push the power switch to (|) for the low speed and to the (||) for the high speed. To turn unit off push the power switch to the center position (0).
Cleaning and general care
• Before cleaning/maintenance, switch the equipment off and remove the main plug from the socket.
• Never immerse the unit in water.
• Each time after use remove any hairs from the cutting blade using the cleaning brush.
• Clean the body of the clipper with a soft, damp cloth. Never use solvents or scouring agents.
• The blade set should be cleaned and oiled frequently with Wahl Clipper Oil in order to maintain its good cutting performance and thus ensure a long service life.
• The blade set should be replaced if the cutting performance is reduced after extended use despite regular cleaning and lubrication.
• During use always be sure the cord is not twisted or running over any sharp objects that might cut the cord insulation.
Cord
If your clipper has a polarized plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits in a
polarized outlet only one way. In the event the plug does not fit fully in the outlet, reverse the plug. In the event it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any way.
Cleaning the air filter
(not available on all models)
• Clean the air filter once a week or more often if necessary.
• Remove filter cover and clean air filter with cleaning brush.
• Snap the filter cover onto the clipper until it click locks into place.
What to Do if the Blade Latch is NOT in the Upright Position FIG.2
• You will need a small flathead screw driver or another strong object with a flat edge
• Place the flat edge to either side of the blade latch to pry up
• Be careful not to pry up the blade latch toward the top of the clipper as there is a chance the drive tip could be damaged.
• Now you can attach your blade
94612-004 Two Speed 2016 Final.indd 2
FIG.1
10/21/16 11:59 AM