Operating The Appliance - Sencor STM 3010WH-NAA1 Manual De Usuario

STM 3010WH-NAA1 / STM 3011GR-NAA1 / STM 3012BL-NAA1 / STM 3013OR-NAA1 / STM 3014RD-NAA1
STM 3015VT-NAA1 / STM 3016YL-NAA1 / STM 3017TQ-NAA1 / STM 3018RS-NAA1 / STM 301XXX-NAA1
3. Removing the attachment and mixing bowl
3.1 Release the arm A7 by pressing the PUSH button A8 and tilt it upwards. The arm A7 is locked in
the open position when the PUSH button A8 slides out together with an audible click.
3.2 Hold the attachment and gently push it towards the mixing head A6. Then rotate it clockwise until
it is released from the motor shaft and remove it. Turn the mixing bowl A4 counterclockwise and
take it off the base unit A5. Move the arm A7 back to the horizontal position.

OPERATING THE APPLIANCE

1. Unwind the necessary length of power cord from the compartment Aqa.
2. Release the arm A7 by pressing the PUSH button A8 and tilt it out.
3. Place the ingredients into the bowl A4 that is seated in the base unit A5.
Attention:
The maximum weight of the ingredients that can be processed in a single batch is 1.2 kg. When
preparing bread dough, do not process more than 600 g of fl our at once. When preparing dough
for sweet pastries (fruit cakes, etc.) it is possible to process no more than 450 g of fl our at once.
The maximum number of egg whites that can be whisked at once is 8.
4. Press the PUSH button A8 and tilt the arm A7 together with the attached attachment to the
horizontal position.
5. Make sure that the food mixer is correctly assembled and that the speed control knob A9 is set
to position 0 (stand-by mode). Connect the power cord to the el. power socket. Connection to
a working power socket is indicated by the speed control knob A9 being lit.
6. Use the speed control knob A9 to set the required speed level from 1 to 6. First, set a lower speed
to prevent ingredients from being sprayed around. As soon as they are mixed together, increase the
speed to the required level. The speed can be adjusted at any time as required.
The pulse mode is used for increasing the speed to maximum for a short time. To activate the
pulse mode, turn the speed control knob A9 to the PULSE position, and to ensure continuous
operation, hold it down in this position. As soon as you release the speed control knob A9, it will
automatically return to position 0 (off).
Attention:
If it is necessary to wipe ingredients off the inside of the mixing bowl A4 and the attachment,
fi rst turn off the food mixer by setting the speed control knob A9 to position 0 (stand-by mode)
and then unplug it from the power socket. Then wipe away the ingredients using a plastic
spatula.
The maximum operating time is 6 minutes. Do not leave the appliance in continuous operation
for longer than indicated above. This is especially true under a heavy load (e.g. when processing
heavy, thick doughs). If the appliance is in operation under a heavy load, allow it to cool
down for at least 10 minutes before turning it on again. At lower loads, a cooling time of 3 to
5 minutes is usually suffi cient.
7. After you have fi nished using the appliance, set the speed control knob A9 to position 0 (stand-by
mode) and disconnect the power cord from the power socket.
8. Disassemble the food mixer according to the instructions included in the chapter Assembling and
disassembling the appliance. Use a soft plastic spatula to remove mixes from the mixing bowl A4
and the attachment.
9. Clean out the food mixer after each use according to the instructions in the chapter Cleaning and
maintenance
2014
Table Mixer
EN-6
11/2014